No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Alden C
Comentado en los Estados Unidos el 12 de junio de 2024
This thing works great for repairing the partially-cut threads of a cheap imported tool that I bought. I just hooked it up to my drill/driver and the shape of this tool fits into the thread grooves easily. Make sure to use light pressure so it doesn’t grab and it works really well. If you have a lot of threads to repair, I’d suggest either buying a few of these or just picking up a proper tap and die set because the crushed diamond abrasive does wear off eventually, but if you have a smaller amount of threads to repair and don’t want to spend the big bucks on a nice tap and die set, this thing is perfect for the job.
Jeff Walters
Comentado en los Estados Unidos el 13 de diciembre de 2024
I got this because it could be used on any sized threads. I had a couple threads on a chainsaw flywheel that were messed up so I couldn’t get the nut started. I found this very easy to use & fixed the problem, saving me a lot of time & money. The product itself is high quality. Definitely worth the money.
Dale
Comentado en los Estados Unidos el 11 de julio de 2022
I bought it to use in my shop in place of a thread file. It's smaller than I expected but that's a good thing. Has been useful and effective.
Rob V.
Comentado en Canadá el 30 de noviembre de 2022
Used to restore threads on some coilover bodies. Worked great. Much better than buying a large expensive thread chaser if all you have are a couple damaged threads.For external threads, a thread restorer file may work a bit better/faster. But internal threads is where this product shines.Saved me a bunch of money, thanks.
OLarryR
Comentado en los Estados Unidos el 14 de junio de 2019
I removed the grab rails off my sailboat to remove layers of varnish and then apply teak oil before re-installing. The nature of these grab rails are that they have 7 stud bolts on each of the two rails and they firmly attach the rails to the top of the cabin - The studs pass thru drilled holes in the Fiberglas and then washer, lock washer and nut hold the rails firmly on top of the cabin. The bolt head end of the stud is not visible - It is inside the top of the rail and wood plugs contoured to the top of the rail hide the bolt heads. These studs should never have to be removed from inside the rail and to do is a chore since the plug would have to be drilled out and a new one installed and contouredmto the rail. Initially, when I removed the nuts from the studs inside the cabin, one of the nuts was had to unthread from the stud and the stud started to rotate within the rail. So, I had to use pliers to hold the stud tight and another set of pliers to unthread the nut. When it was time to re-install the nut, I could not thread it onto the stud. My pliers had ruined the lower threads.I was considering using a diamond cutoff wheel on my Drexel to remove the lower threads but that would leave few threads available to re-install the nut and besides The nut was had to unthread it initially, so I would still be face with that problem as well.I then discovered the EZThread 382 searching the web and Amazon for solutions either by buying a different type of fastener to clamp to the existing threads but then I came across this tool to repair existing threads.The 382 mini-grinder tool was easy to use. It just about 1-2 minutes of use, I was able to get the nut back on. But other threads made it hard to completely re-install the washers and nut, so I tweaked addl threads and kept testing how easy it was to completely install the nut. After only another few minutes of tweaking the threads, the nut washers and nut were able to be re-installed easily. Since I was now able to rethread the nut all the way up to the inside cabin top, the friction fit at the bolt head kept the stud from rotating within the rail and I was able to torque the nut fine. So, this tool not only repaired the initial threads to get the nut on but tweaking the rest of the threads enabled me to utilize the stud, get a tight fit, without having to replace the stud which would have been a much longer repair and would have required labor to replace and contour a new plug on the outside of the rail.This is a great tool ! I am telling all my friends about it !
Productos recomendados
Mex $199.99
Mex $ 115 .00 Mex $115.00
Mex $1,203.00
Mex $ 481 .00 Mex $481.00
Mex $482.65
Mex $ 226 .00 Mex $226.00
Mex $255.00
Mex $ 130 .00 Mex $130.00