No hay artículos en el carro
No hay artículos en el carroDisco De Corte, Grosor 0.6Mm 36Pz para Metal
laura g.
Comentado en México el 5 de marzo de 2025
Era justo lo que necesitaba porque tengo el Dremel, los recomiendo.
Antonio A.
Comentado en México el 27 de enero de 2025
Excelente desempeño muy recomendable
Clemens Panten
Comentado en Alemania el 3 de junio de 2023
Ich kann die schleifscheiben überall sehr gut gebrauchen!
Paul Cabrera García
Comentado en México el 24 de septiembre de 2023
Producto original y de excelente calidad precio
Josue Cabrera
Comentado en México el 1 de junio de 2021
Tengo la Dremel 3000 y quedan bien.El único detalle, que es esperable por el precio, es que duran muy poco los discos. cortando una lámina regular de muy poco grosor, como la de un microondas, el disco se hace polvo rápidamente, a los 15cm ya no tienes disco. Cortan bien, relativamente rápido, pero sí duran poco. No son para trabajos muy pesados o extensos, toma en cuenta que usaras muchos si cortas metal.
Martha Nelly Flores Lozano
Comentado en México el 9 de abril de 2021
Justo lo andaba buscando y me llegó muy rápido
Phil Crowell
Comentado en Australia el 28 de noviembre de 2020
Used these to cut out rusty fender seams from a 60 year old car. I thought I would use most of the 30 but they did the job really well and lasted.
Cliente de
Comentado en México el 7 de abril de 2019
Corta muy bien los materiales
Cliente de
Comentado en México el 13 de agosto de 2018
Cumplen con su cometido aunque debes trabajarlo con mucho cuidado ya que es un poco fragil
Daniel Flores
Comentado en México el 13 de julio de 2018
Los encontré de oferta, que puedo decir de ellos si son DREMEL muy buena marca y buen producto. Sin duda los comprare de nuevo
S Lindsay
Comentado en los Estados Unidos el 29 de diciembre de 2017
I had previously been using Dedeco cut off wheels and was satisfied with the quality however they were much more expensive than the Dremel. I read a bunch of reviews here that these cut-off wheels would easily crumble and fall apart. I decided to give them a try. Here are my results:1) Just like the Dedeco they are brittle and you must handle them with care especially not to bump side to side2) Don't over tighten the screw in the collet or you'll damage the wheel and it will more easily break3) Use a steady hand(s) when cutting and avoid any side to side movement. Either wheel (Dedeco or Dremel) will break pretty easy if it receives side pressure4) I used the Dremel to cut through heavy duty staples (3/16"). I was able to cut through about 8 staples before having to replace (I had to cut dozens and the results were pretty much consistent). I thought that was pretty impressive. It was also 20 degrees outside. I even had a few wheels grab the stable a bit and they still did not break but any sideways movement they would usually fall apart soon.5) I also used these to cut through an M6 (metric - 6 mm or .24") stainless steel bolt. Stainless is really tough but I was able to cut through the bolt with just one cut off wheel (just barely one).Bottom line - if you hold steady (preferable two hands on the tool), avoid side to side motion, let the wheel do the cutting, don't exert too much pressure, and don't over tighten the collet screw these should work just fine for most small cutting operations. I only cut steel... not sure how it will perform with soft substances such as plastic etc. Soft substances could cause heating and gum up.
Alan heartfield
Comentado en el Reino Unido el 25 de septiembre de 2017
yes they were what i expected , i just had no idea that they were coming from Japanbut the service was superb
David
As Described.
Productos recomendados
Mex $135.00
Mex $ 76 .00 Mex $76.00
Mex $251.75
Mex $ 140 .00 Mex $140.00
Mex $609.59
Mex $ 310 .00 Mex $310.00