Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Kohler GP77548 Kit de válvula Coralais, color blanco

Envío gratis en pedidos superiores a Mex $600.00

Mex $352.84

Mex $ 172 .00 Mex $172.00

En stock

1.Color:Blanco


Acerca de este artículo

  • El producto está fabricado en China
  • El producto es muy duradero y fácil de usar
  • Fácil instalación y fácil manejo
  • Kohler Pieza original
  • Grifos de control único;Control único Coralais;Sugerimos utilizar el kit de junta tórica GP30420 al reemplazar la válvula



Más información del producto

imagen
imagen
imagen

ED
Comentado en los Estados Unidos el 17 de octubre de 2022
Our Kohler faucet began leaking when turned "off". Fortunately I save he original paperwork and had a schematic and part number for the valve. I watched a You-tube video and realized replacing was simple. It's about as easy as changing batteries in a flashlight!! The old valve was hard-stuck to the metal collar and I had to band it loose with vice and hammer. Ruined the old valve but who cares? Re-assembly was a peach and entire job was less than ten minutes. Works like a brand new faucet!! Pays to buy an expensive faucet with replacement valve!!
Ray A
Comentado en Canadá el 27 de febrero de 2021
My faucet now works great again, and a lot smoother than before.
Neeru Choudhary
Comentado en Canadá el 7 de septiembre de 2020
Amazing product..fixed my tap ..I had thought will need to change the entire tap but it was so easy to fix the handle with this little thing. Watch a you tube video before you try to fix. It’s damn easy to follow the instructions shown in the video :)
Michael F
Comentado en los Estados Unidos el 24 de diciembre de 2019
This was the right part for the right problem. Been installed for months and no issues. Fit perfectly. Be sure to replace your rubber o-rings and plastic bearings at the same time with the other Kohler kit GP30420 and use the silicone that comes with that kit. This revitalized an old but beautiful Kitchen faucet that just needed some maintenance after so many years of hard service.
Carlgo
Comentado en los Estados Unidos el 13 de marzo de 2015
My Kohler Fairfax single-level faucet was feeling stiff and funky. It had to be this cartridge, and it was. Now it is silky smooth and I feel much better about things sink-wise as I replaced the side spray as well (another review).You can watch a certain video channel, You know it, and get instructions. Of course it isn't that easy taking apart an old faucet. This is how to do it:1. Pry out the hot/cold cap on top.2. Remove the screw (some may have allen screws, mine was Phillips). Careful as they can be stuck.3. Remove the lever assembly. It too can be stuck. Lift and kind of push back on it. If it is still stuck get a piece of wood, around 3/4 thick, push the lever down at the front and put the wood between the back of the lever dome thing and the ridge on the part below it. Lift up on the handle and the lever assembly will lever off.4. There is now a dome looking thing with the hole in the middle being where the top of the valve sticks out. Unscrew it. Mine was fairly easy, but some may stick. The IMPORTANT thing to do is to not let the body of the faucet turn as that will ruin the little hoses that screw into the faucet. You can buy them, but they are expensive and usually only available on-line. You can try penetrating oil or perhaps a hair dryer, some sort of clever way to get ahold of things and unscrew it.5. Now there is a retainer that holds the valve in. It too can be stuck. Lift up the swiveling faucet and hold the bottom with a pipe wrench or arc joint pliers so that you can apply pretty strong pressure on that top nut. The bottom wrench should be on the skinny lower part, not up where the faucet parts rotates around.Again, DO NOT LET THE BODY PART ROTATE.6. Lift out the valve. It has a gasket on the bottom. Make sure the old one is out of the faucet. Sometimes they come off of the old valve and you don't want two gaskets. Drop the new one in. Note that there are two protrusions on the valve that fit into depressions in the valve.7. While the rotating faucet part is off, clean the surfaces and lube the O-rings with silicone lube. I suggest ordering the O-ring kit at the same time as the valve, cheap enough and it comes with the lube. The faucet will leak at its base if these seals are bad. The swiveling action will again be nice.If things are really stuck, take the faucet out and deal with it on a bench.Assembly is easier than taking apart old plumbing parts. You will have a nice, smooth faucet that was not cheap to buy, has parts available to fix it and can probably be kept going for decades. I have done all the above and it is exactly as good as new now.
Productos recomendados

Mex $207.73

Mex $ 110 .00 Mex $110.00

4.9
Elegir

Mex $302.01

Mex $ 163 .00 Mex $163.00

5.0
Elegir

Mex $2,336.21

Mex $ 957 .00 Mex $957.00

4.5
Elegir