No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Accusize Industrial Tools EG06-1002 Juegos de cables de medición de rosca métrica y EE. UU
Accusize EG06-1002 Juegos de cables de medición de roscas métricas y EE. UU
48 piezas, 16 tamaños diferentes para todas las 60 roscas. Mide todas las roscas de 3 a 48 roscas por pulgada y todas las métricas de 0,5 mm a 6 mm. Método de 3 cables para medir roscas externas. Los cables se instalan en una caja de plástico estampada con tamaños. Tabla laminada cumplida con los Estados Unidos Manual estándar H.28. Proporciona tamaños y medidas adecuados sobre cables.
Los cables de medición de rosca y un micrómetro se utilizan para medir rápida y con precisión los diámetros de paso de las roscas externas. Viene con 4 soportes de alambre de medición de rosca
Método de tres cables para verificar el diámetro de paso de las roscas de tornillo
M = Medición sobre cables. E = Diámetro de paso de la rosca D = Diámetro principal básico o exterior W = Diámetro del alambreP = Paso de rosca M = E + ConstE = M - ConstConst. = 3W – 86603p (se encuentra en el gráfico)
El diámetro de paso máximo y mínimo (E) para cada clase de rosca se puede encontrar en el manual de las máquinas
Tabla de conversión para hilos métricos de 60°
Tabla de roscas para todos los EE. UU. HILOS DE 60°
Selecciona el tamaño adecuado del cable para el número de roscas por pulgada (US) o el paso de rosca (métrico)El troquel de paso métrico medido (E) es igual a la medición sobre cables (M) menos decimal en la columna "CONST". Nota: PD básico. es igual al diámetro principal básico más decimal en la columna "ADD" menos decimal en la columna "CONST"
Jim Clark
Comentado en Canadá el 3 de junio de 2024
I'm just learning to cut single point threads on a metal lathe. These were helpful to assess the Pitch diameter and to help understand where my cut threads were binding on the nut. In hindsight, probably not necessary, but they were helpful in the learning curve. The .029" wires measured between .02880 and .02905 on my Mitutoyo micrometer. I bought this set mainly for the box that looked easier to find on the shelf. It is fine, but the lid is very tight, and I need to use a thin blade knife to shoe-horn the lids off and on. It looks like the tabs on the lids would break if you try to twist the lid off by hand. The included black rubber wire holders were a good addition. They hold 2 wires on the micrometer and were helpful to measure the threads while on the lathe. Overall pretty happy with this purchase.
Chad Lombardo
Comentado en los Estados Unidos el 14 de junio de 2024
Works like a charm with little effort
Dwayne Westley
Comentado en los Estados Unidos el 24 de diciembre de 2024
These work very good.
Korova Milk Bar
Comentado en los Estados Unidos el 13 de octubre de 2024
MUST screw or nail this to something that cannot slip around whether a board or table .. love the magnet which holds the metal cap and the smooth fit as it bottoms out securely on the bottles rim. You feel it seal and know that beer looking back at you is 7 days from consumption. "POP" Oh yaaa....Quality materials and simple leverage design YET speedy capping pays for itself.
Terry DeWarle
Comentado en Canadá el 3 de enero de 2024
Very nice work , very accurate.
naghme
Comentado en los Estados Unidos el 6 de febrero de 2023
As a professional brewer, take my word, THIS IS JUNK. I purchased so my guys in the cellar could do some single bottles occasionally for samples. We did maybe 3 cases and realized that it does not evenly seat the cap, thus, resulting any leaky caps and flat beer. Do yourself a favor and spend the money from a reputable dealer for something like this. You worked too hard on that beer to let it go to waist. Cheers
marcarthur baralla
Comentado en los Estados Unidos el 24 de noviembre de 2023
The item came with a missing screw (no pb, I just put on one I had) but most important it does NOT work with 29mm bottle caps. very disappointed.
Parasz
Comentado en los Estados Unidos el 26 de marzo de 2022
I've bottled over 300 bottles of beer with this with no problems... it is starting to feel a bit loose, but still works fine. Much better than the "Wing" Style"You need to put a bit of muscle behind it, but nothing a 100 lb 14 year old cant do.You really need to clamp or screw it down to get the best use out of it.The magnet has not fallen out of mine as others have stated.I have found some beer bottles work better than others (I prefer New Belgium) and an easy test is if the lid twists after seating.... maybe don't use those bottles again. So far I have none that have burst or failed to seal after carbonation.I shouldn't have to say this but it WILL NOT work well on twist top bottles.
anton oster
Comentado en Canadá el 9 de mayo de 2021
Great wires for thread measurement. While I will always use threads mics over wires, sometimes I don't have mics available, or large enough. These are inexpensive and arguably more accurate than thread mics, they just take longer to set up, calculate mow (measurement over wire) and are hard to hold on to. Bought a set for home and work.
Michigan Craftsman
Comentado en los Estados Unidos el 31 de mayo de 2020
Lovin' this wire set. Spot on dimension, wire holders work well. Case is a little hard to open when new, but seems better with each use. Great set for the home workshop.
Productos recomendados
Mex $1,991.88
Mex $ 796 .00 Mex $796.00
Mex $326.09
Mex $ 172 .00 Mex $172.00
Mex $612.68
Mex $ 324 .00 Mex $324.00