No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Características del producto:
El mango de aire caliente y el soldador eléctrico están conectados e intercambiables independientemente, uno del otro es independiente, fácil de reemplazar, pantalla grande azul de doble pantalla, ajuste de temperatura del botón de pantalla digital, ajuste preciso y temperatura de control + 1 °C, rango de ajuste de temperatura de 100 °C a 480 °C (100 °C a 480 °C), tolerancia de temperatura es de + 2 °C.
Pistola de aire caliente de gran capacidad, calienta rápidamente, viento suave y grande, apto para trabajos sin plomo y plomo. El diseño más científico y de moda dos en uno, equipado con carcasa de plástico ABS de alta calidad, la máquina es compacta y duradera.
Toda la máquina adopta un diseño antiestático, elimina eficazmente el daño de los componentes SMD. También tiene la función de auto-detección de fallas y advertencia de fallos.
El producto adopta una pantalla grande, resaltado azul, doble botón de visualización digital, ajuste de temperatura, que puede mostrar la temperatura precisa.
Trabaje estrictamente de acuerdo con el manual de instrucciones y los procedimientos.
Asegúrese de que la pistola de calor debe estar cerca del soporte antes de encender la máquina para lograr el efecto de inducción.
Tenga en cuenta que
Antes de arrancar la máquina, asegúrese de que el cable de alimentación esté firmemente conectado a la máquina hasta que se pueda encender normalmente. La máquina puede funcionar normalmente solo cuando normalmente está encendida.
Sistema de inducción
El mango de la pistola de aire caliente es un sistema de inducción. Después de conectar la máquina a la fuente de alimentación, asegúrese de que el mango de aire caliente se coloca en el soporte antes de abrir. Luego encienda el interruptor independiente de la pistola de aire caliente y levante el mango para entrar en el estado de trabajo.
Diseño de interruptor independiente
Conecte el mango del soldador y el mango de la pistola de aire caliente con la interfaz correspondiente. Después de encender la alimentación, encienda el interruptor independiente correspondiente y coja el mango para entrar en el estado de trabajo.
Accesorios auxiliares
- 10 puntas de soldadura
- 1 bola limpia
- 1 esponja absorbente
- 1 mecha CP、 1 colofonia
- 1 cable de soldadura de cobre
- 2 cables de soldadura
- 3 pinzas antiestáticas
- 1 extractor IC
Consejos de seguridad
!El voltaje de este producto es 100-120v 60Hz.
!Asegúrate de utilizar el voltaje correspondiente en tu dirección. Si de acuerdo con el voltaje anormal, causará daños a la estación de soldadura, o los componentes de la máquina se romperán debido a la alta tensión.
!Para garantizar su seguridad personal, por favor, apague el interruptor de alimentación principal y desenchufe el cable de alimentación Después del trabajo.
!Asegúrese de colocar todas las piezas después de que se hayan enfriado.
MYPOUOS 2 en 1 Estación de soldadura de lista de embalaje
Configuración estándar
1 estación de soldadura 2 en 1 8588D
1 mango de soldador
1 mango de pistola de aire caliente
4 boquillas; 1 cable de conexión
1 soporte; 1 manual de instrucciones (idioma español no garantizado)
Servicios prestados
1. Los productos son entregados por el servicio logístico de Amazon
2. Si encuentras algún problema cuando recibes los productos, estamos muy contentos de resolverlos por ti y te proporcionaremos una respuesta satisfactoria.
Mister MPR
Comentado en los Estados Unidos el 16 de febrero de 2025
I think that there are better units out there but for the price of this one I think you'd be hard pressed to find a better performing combo. It heats up fast and has lasted me for quite awhile using it almost weekly for about a year now. I'm just a hobbyist and not a professional but I am generally pleased with the ease of use this things has provided me. Straight forward and easy to use. Much better than your regular old soldiering iron. The hot air gun comes in clutch especially when trying to desolder components from a pcb.
Jathuron
Comentado en los Estados Unidos el 13 de julio de 2023
I got this in because my old setup is getting outdated. I had this item for almost 2 months before I opened it. Once I did it happen to be when I needed it the most for an emergency. Well when I opened I was really impressed with the features and adjustments for the solder & the heat gun. Well needless to say the solder iron did not work. SO I had to order another iron and this one is a 6 point connector which made it a little more difficult to find but I did and it works. So the good thing about this is that I know I can always have another iron brand work with this station.I am only giving a lower rating based on the iron did not work right out of the box and had to be replace. I am very happy with it's performance so far. Good value and I recommend this item.
BrianE
Comentado en los Estados Unidos el 5 de julio de 2022
I was skeptical at first when looking for a decent soldering station for my auto shop to replace BMW MOSFETTS in the engine computers. First off it was packaged really well with no broken or missing pieces. Second, it was easy for the tech to operate and use this station for the first time and it went very well. I have spend hundreds on well known name brand setups that were over complicated, difficult to maintain heat ranges and were bulky. Definitely a must for those who are starting out with electronic components.
Angel
Comentado en México el 22 de mayo de 2022
Deberían vender Repuestos y/o ofertarlos =(
Peter
Comentado en Canadá el 25 de diciembre de 2020
This is a very tidy little unit that works well as advertised. It is perfect for occasional use in a home shop but it likely won't stand up to daily commercial use.Plusses:- Individual temp readouts and on/off switches for iron and air gun- Reasonably high power/effectiveness (iron can heat decent loads and gets up to temp quickly from idle- Kit is complete with everything you *need* for low volume soldering and reworking and then some.- Cooldown with power off works properly. This is rare IMO. Note that there is no "master power" on the mains. Please plug this into a switched power bar and remember to turn it off once the unit has cooled down and you are not going to be using it for a while!Minuses (i.e. why it isn't suitable for constant use by a pro):- No apparent way to disable sleep mode on the iron (odd IMO)- Iron pen handle is very basic and all plastic. I just know it is eventually going to fail where the tip holder threads on. No insulating collar.- I suspect the displayed temperatures are quite inaccurate (low) but I have not confirmed this except by experience.- Tips (many!), tweezers, supplies are all pretty basic and made of weak/cheap materials so you'll want to replace the ones that you actually use (but it is nice to have the assortment on day one)For occasional work, it will do the job well and is a bargain for the money. I'm very happy.
Justin
Comentado en Canadá el 18 de diciembre de 2020
So I ordered a 858D from somewhere else on Amazon and honestly it was pretty poor, this however is pretty alright, not perfect but more than usable.I've opened up ever part of the unit and inspected it, and I'm happy enough with it, everything is wired up right and grounded out so a set up from the 858D I had returned.The heat gun itself uses a ceramic core, so it's more consistent than a Mica core on a cheaper unit, it is grounded out with the wire being soldered to the very top end where it's cool, I'd have liked to have seen a tab where it's terminated so when you replace the core you can just take the whole enclosure for the core out.If you have a rattling fan it's just misaligned open it up and put the fan and grommet in the top part that has no PCB and put it back in place, my fan did not rattle before I took it apart to inspect, so it's an installation error.The soldering iron is a lot better than I was expecting, I have a KSGER 12T 3.1S on that way, but it won't be here for a while due to Canada post being slow as possible, so it's nice to have an iron in the meanwhile so I don't have to use my horrible old one.It heats up fast around 10 seconds or so to usable so pretty good, all the tips are cheap but useful, dirt cheap to replace over T12 tips even if those are far better but still a good AUX Iron.When you get your unit to NEED to calibrate it with a temperature probe using the pots inside the unit on the face plate.If you need to calibrate your probe just use rolling boiling water since it's more or less 100C always, The hot air gun is pretty easy to set but if you don't have a soldering iron probe it may be a pain to do, but it's worth the effort, it may take you an hour to set your calibration.The unit itself is nice enough, cheap in the way it's ABS plastic but in other ways very nice to use, If you intend to use this for long amounts of time and constantly all day I'd consider adding in a Fan inside the unit to cool the transformer.
Productos recomendados
Mex $299.00
Mex $ 152 .00 Mex $152.00
Mex $278.24
Mex $ 141 .00 Mex $141.00
Mex $209.00
Mex $ 117 .00 Mex $117.00