No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Xadnitu 1/2" EMT a EMT Conector de 90 grados
Para la gestión de conductos.
Calidad fiable
Tiene la estructura de las certificaciones de fundición a presión, UL y CSA.
Superficie brillante
El acoplamiento EMT tiene una superficie lisa, lo que permite un uso más seguro y cómodo, evitando arañazos en las tuberías.
Incluye tres componentes
Piezas de montaje
- una pieza de conector de ángulo recto
- una funda extraíble
- cuatro tornillos combinados
Adecuado tanto para uso en interiores como en exteriores
Amplias aplicaciones
Fábrica, jardín, hogar, construcción y otras aplicaciones necesitan conectar tuberías
Puede acomodar tubos o tubos con un diámetro máximo de 1/2 pulgadas.
- Prevención de la corrosión
- Resistencia al desgaste
- Resistente al óxido
- Construcción de fundición a presión
- Certificación UL
- Listado CSA
The Nelsons
Comentado en los Estados Unidos el 17 de marzo de 2025
These are great EMT 90 degree screw connectors for electrical conduit work. I couldn't find any real differences between these and a pack I picked up from the box store. Pipe hole size was correct, and the EMT inserted with the right amount of play, and I had no thread issues tightening down the connector to the pipe. Great value!
Cycletime 71
Comentado en los Estados Unidos el 17 de marzo de 2025
I used these 90 degree elbow connectors for installing a motion sensor light on my brick house. Everything went together without issue.
S. Meyer
Comentado en los Estados Unidos el 16 de marzo de 2025
These work great for keeping inside conduit corners tight to the structure they are mounted to. I’m using them in a storage shed where I don’t want any chance of someone hanging items from exposed conduit. Because of the tight turn on these I only pulled wire through one fitting at a time. The removable cover made this easy.Smooth radius bends in conduit are preferred for pulling wire, and wires can be pulled through a total of 360 degrees at one time. Not so with these. But if bending conduit won’t work for your application then these are helpful.One note; these are made of zinc alloy and will break if under tension. Nothing unusual about that as most 1/2 inch conduit fittings are zinc.Steel fittings are available at electrical suppliers houses.
YKNOT
Comentado en los Estados Unidos el 22 de febrero de 2025
Fits 1/2 inch EMT just right. These make a clean, compact 90 degree turn while still allowing easy pull of wires with the pull access. I'm going to get more of these.
R. Moheban
Comentado en los Estados Unidos el 23 de enero de 2025
I expect these metal conduit ells have no trouble meeting building codes. They appear to be the same quality as EMT connectors typically found at home improvement stores. The construction is all metal.The removable plates allow plenty of room for pulling wires straight. Sometimes wires simply won't pull when going around corners; these fittings eliminate the corner problem. They also eliminate having to make double bends in a piece of conduit. I've mangled more than one job by trying to bend a single piece in two directions. If I had these 90 degree fittings I could have made just a single bend and gotten a much more professional result.Inspecting all the 10 pieces I couldn't find any flaws. A couple of screws had fallen out but I found them in the bag. The manufacturer could ensure the set screws are screwed in further so they don't fall out in transit, but it's a small quibble.While ten of these costs currently around 22 dollars, as I don't know whether that price is typical or high, I will rate this product five stars as a good, suitable product with good quality control. As for the value buyers may want to comparison shop.
Productos recomendados
Mex $698.94
Mex $ 342 .00 Mex $342.00
Mex $370.00
Mex $ 185 .00 Mex $185.00
Mex $426.43
Mex $ 213 .00 Mex $213.00