Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Weller EC234MX Elemento Calefactor para Wtcptmx

Envío gratis en pedidos superiores a Mex $600.00

Mex $556.71

Mex $ 261 .00 Mex $261.00

En stock

Acerca de este artículo

  • Modelo # EC234EC234
  • Requiere un nuevo conjunto de tuerca de barril BA60 si el EC234 se está utilizando en planchas fabricadas antes de 2000
  • Fabricado en México
  • Dimensiones del paquete: 1.25 pulgadas de largo x 1.25 pulgadas de ancho x 5.0 pulgadas de alto


Punta de destornillador de la serie CT5 para soldador W60P y W60P3. Color: negro. Fabricado en México.


SA Baker
Comentado en los Estados Unidos el 22 de julio de 2024
I have had this Weller soldering iron set for 40 years. It finally stopped heating. After doing a bit of research, I purchased this part of the iron ( Must also purchase BA60 Barrel nut. old one will not work). Removed two screws, pulled out the old, reseated the new one. Bingo. I have heat again.Excellent product. Please note, you must purchase the appropriate barrel nut. Your old one will not fit.
ULISES SANDOVAL CARDOSO
Comentado en México el 25 de marzo de 2024
Excelente calidad funciona perfectamente solo el empaque viene muy frágil
Diivious
Comentado en los Estados Unidos el 10 de diciembre de 2024
Not a good ft.1_ the 2-up pins are slightly miss alighted, meaning you have to force it on to get the element screwed down to the handle.2) Once you have it on the handle, the bit sleeve will slide on due to this one heating element having a 'shoulder'. meaning its to large a diameter.
Hector
Comentado en los Estados Unidos el 28 de septiembre de 2023
fits only that you need the a new barrel nut assy. Should just come with one I would think a kit like for the older models
Crisco
Comentado en los Estados Unidos el 28 de junio de 2021
This is NOT the same EC234 that came off my iron. This heater is bigger around as you can see from the flare about half way down in the picture. As a result the original Barrel nut will not fit over it. My iron clearly has written on it to use EC234 heater so I know I ordered the correct part number. I took a chance and ordered a replacement barrel nut to see if perhaps there was a design change to both parts.Update: I apparently guessed right. I ordered a replacement barrel and it fit this heater. The moral of this story is that at some point the EC234 underwent a design change and Weller did not change the part number.
R H
Comentado en los Estados Unidos el 10 de enero de 2021
This updated element worked perfectly on my old Weller solder station. Only con, I had to purchase a new tip retainer because the barrel of the new element is thicker than the old.
Byroom
Comentado en México el 17 de junio de 2020
Funciona el remplazo , lo que no me queda claro es el color bronceado que tiene la pieza en uno de los extremos, de eso funciona en optimas condiciones.
Jose Ismael Morales Sandoval
Comentado en México el 31 de marzo de 2019
Se daña muy rápido
Productos recomendados

Mex $324.00

Mex $ 149 .00 Mex $149.00

4.4
Elegir

Mex $438.97

Mex $ 215 .00 Mex $215.00

4.8
Elegir

Mex $491.07

Mex $ 240 .00 Mex $240.00

4.6
Elegir

Mex $287.64

Mex $ 152 .00 Mex $152.00

4.5
Elegir