No hay artículos en el carro
No hay artículos en el carroDescripción del producto
1. El tubo interior debe inflarse ligeramente antes de la instalación (máx. 0.35 bar/5 PSI
2. Utiliza cinta adhesiva para llanta y asegúrate de que la llanta sea lisa y última intervensión de materias extrañas.
3. Asegúrate de que la válvula esté alineada perpendicular al borde ya que se ajusta a través del orificio del vástago de la válvula en la llanta, y la parte inferior de la válvula está en pleno contacto con el interior de la llanta.
Ken J
Comentado en Canadá el 27 de febrero de 2025
This is my third purchase of this Youyoute Mini Heater. I use them in my three resin printers. I set the temperature to 30C and after about 30 to 45 minutes the resin is up to print temperature. Printing this warm helps a lot with getting good prints with very little print fails. I find it especially useful for heating a rubber like resin that I use because if cold it's like syrup and thick. Heating it to 30C makes it print perfectly.
Hernán B.
Comentado en los Estados Unidos el 29 de agosto de 2024
If you print with resin during colder months, the Youyoute Mini Heater is a game-changer. This heater is fantastic—super easy to use and practical for keeping your printer warm. Since I started using it, I’ve noticed a significant improvement in my resin prints, with far fewer defects. I only had to make a small modification inside the lid of my Phrozen printer to route the cable, but it was totally worth it. The heater is compact yet highly effective, and it’s become an essential part of my resin printing workflow.This is definitely a must-have for anyone dealing with low temperatures while printing in resin!
Rodrigo G
Comentado en México el 4 de junio de 2024
MUY LIGERAS PERO LA VALVULA ES DE PLÁSTICO SE SIENTE FRÁGIL.
Daniel Rodriguez
Comentado en México el 22 de junio de 2024
Al inicio todo iba muy bien, ahora el aparato no me mantiene la temperatura programada, si lo pongo en 30 grados, se sube hasta 36. En ese aspecto muy mal
Jonathan Carter
Comentado en los Estados Unidos el 19 de junio de 2024
Bought this as a lightweight tube to carry in my camelback while MTBing. Got a flat. Tried using this tube, but unfortunately the valve stem is made of plastic and broke - easy to do when you connect your pump and inadvertently torque it a bit (as I did). Fortunately for me I was with a group and somebody else also had an inner tube for me. Otherwise it would have been a long hike-a-bike back to camp. Would skip this product and pick one out that has metal valve stems that won't break on you.
FEY Pierre
Comentado en Alemania el 1 de febrero de 2024
kleines kompatkes Gerät was hilft die Temperatur in meien 3d-Drucker kasten stabil hält. Vorheizen des Kasten baucht lange wenns die Raumtemperatur sehr kalt ist.
Sean Graham
Comentado en los Estados Unidos el 25 de diciembre de 2024
Started to see a lot of support failures as the temperatures dropped. Added to my Anycubic PhotoMono2 and used to warm resin, vat, and build plate. Instantly restored print success to summer temperature performance. Holds very stable temperature once set. Had to make a small cut-out for the cable 8n my cover, but install and startup were very easy after that.
Javier
Comentado en los Estados Unidos el 22 de octubre de 2024
La pise en la paleta, quedo perfecta
Luis Felipe Sanchez Curiel
Comentado en México el 21 de octubre de 2024
Funciona muy bien
John Karwoski
Comentado en los Estados Unidos el 17 de enero de 2024
I haven’t ridden with this inner tube yet. It is a backup to carry for my tubeless tires. You can find lots of reviews from other people riding with RideNow TPU tubes to learn about their experiences.This RideNow tube is labeled as fitting 32mm to 47mm tires, so is perfect for my 38mm and 42mm tubeless tires.I weighed this RideNow tube (including paper wrap) at 46 grams compared to 101 grams for the butyl tube it’s replacing. The RideNow tube also requires much less storage space (see picture).My wheel rim is 32mm deep. RideNow’s 45mm valve is the right size for me ( see picture).No patch kit is provided. You need to find your own TPU tube patch kit. The valve core is not removable, and there are no threads on the valve stem. A screw-on air pump head may have difficulty holding onto this valve.Instructions are provided in tiny font but are well written and understandable (see picture).My recommendation is to try out this tube. Maybe carry two. The two RideNow tubes will still be smaller/lighter than the usual single butyl tube.
Outdoor Ranger
Comentado en los Estados Unidos el 20 de agosto de 2023
Surprisingly lightweight for the price, the TPU inner tube allows the front of my bicycle to feel nearly weightless while lifting it and the generous sizing allowed me use a 20x2.15” tire. It also comes with a sticker.
MR D.
Comentado en Australia el 3 de julio de 2023
I've been using this for a few weeks now and it works flawlessly. It does a great job of keeping the resin and internal print area warm. I've set it to 28°C and it has no problems maintaining this temperature for several hours at a time (longest print so far using this was about 9 hours 40 minutes) within the printer while outside the printer was getting down to 6°C at times.I did have to buy a lead with an Australian plug to fit into the converter, so I could plug in into the mains power, which cost about $12 from Jaycar, but was happy to do so to be able to use such an excellent little device.I would like to see an option where this could plug straight into the USB sockets in the Elegoo and Anycubic printers that have them for the air purifier, which I think are 24v. Having an air purifier on one side and this heater on the other would be great.
Productos recomendados
Mex $299.00
Mex $ 161 .00 Mex $161.00