No hay artículos en el carro
No hay artículos en el carro Especificaciones:
Número de modelo del artículo: QYZDGYSHGJV1 (EE. UU.), QYZDGYSHGJV2 (UE), QYZDGYSHGJV3 (AU)
Potencia: 6000 W.
Área de secado: 485 x 540 mm.
Peso neto: 24 kg (accesorios incluidos)
Contenido del paquete
1 secador de flash.
3 llaves.
1 destornillador.
1 manual de usuario (idioma español no garantizado).
JASON CRABTREE
Comentado en los Estados Unidos el 15 de enero de 2025
my only complaint is that the stand isnt very stable for how heavy the top is. aside from that it works well and covers a large area.
Loyaler
Comentado en los Estados Unidos el 8 de agosto de 2024
Photo and video will come soon when I send a new update. I have not used the product just yet but thought I'd share some information to help you with your purchase.Disclaimer: I am not a licensed electrician. Electricity, especially when working with 220V or electrical panels, is extremely dangerous and can cause serious injury or death if not handled properly. It is crucial to consult with a professional electrician for the proper installation of any electrical circuits and components. The information provided below is based on my personal experience and should not be considered professional advice. I take no responsibility for any errors, omissions, or damages resulting from the use of this information. Always seek professional guidance for electrical work.Installation Requirements12mm wrench (replaces whats provided to make install of casters easier)Screw Driver (philips & slot) for easier install (screw driver is provided in packaging)Male plug for 220vA 220v circuit (standard household 110 will not work)PLEASE VERIFY THE FOLLOWING - DON"T TAKE MY WORD FOR IT220v 6000W heater. On vevors page I found a recommended 28 amp circuit. I'm still verifying this info with vevor directly. Calculations on wattage puts us at 20 amps (i'm not an electrician I Googled it).InstructionsInstall casters to bottom base. They screw in. use 12mm wrench to make it easier.Install bottom tube support (has two nuts on the tube at the end, this is for adjustments)use the provided hex nuts and bolts. No need for a wrench with the bolts. Get them hand tight and they grip on their own. use provided hex or your own to finish tightening.Pull the top unit out of the box and lay upside down on a table. Install the second tube (i used washers here).Next is step 2 in the manual.Find the heating elements in the white plastic rectangular box. They are encased in bubble wrap. Do not handle these with your bare hands. It will shorten the life of the bulbs. I used rubber gloves to hand them.Place the heating elements inside the head unit. The ceramic ends of the elements go into the metal clips. The white wires from the ends will be secured inside the ceramic housing. I used a slot scew driver. You will need to unscrew the posts a bit to get the wire inside the ceramic housing. Tighten the screw when the wire is inside. Pull gently to ensure it is secured.With help, place the head unit (the long black tube) into the base (black tube) and use provided hand bolts the secure the unit at the prefered height.The sensor on the side needs to be properly installed. Unscrew the two screws sticking out of the side of the head unit. Place the bracket against the head unit and replace the screws.Install your male plug for 220v circuit (plug depends on amps being used)
Productos recomendados
Mex $9,921.83
Mex $ 1,881 .00 Mex $1,881.00
Mex $450.33
Mex $ 211 .00 Mex $211.00
Mex $3,523.63
Mex $ 1,691 .00 Mex $1,691.00
Mex $191.72
Mex $ 115 .00 Mex $115.00