No hay artículos en el carro
No hay artículos en el carroSynology 10Gb Ethernet and M.2 Adapter card E10M20-T1, RJ-45; 1 port
Customer Review
Comentado en los Estados Unidos el 8 de enero de 2025
But it really does work great. NAS is soooo much faster with this card installed. I'm using dual 2TB NVMe for the cache. Really happy with this card. Recommended!
Iosif T.
Comentado en Canadá el 29 de enero de 2023
I did bought this one in order to replace the working (for several years already) Synology M2D17 M.2 and to add 10Gb network (Bell has now 3Gb speed, possible 10! in the near future)Didn't accepted the previous two NVMe 500 Gb cardsBough then two M.2 2280 NVMe SSD SNV3410 800GBNeither those workedUnsure if I want to keep-it and go back the cards which actually worked as cache
Bian Xi
Comentado en Singapur el 10 de marzo de 2021
Good
Edward Smith
Comentado en los Estados Unidos el 26 de febrero de 2021
I bought this and it didn't work in my particular Synology NAS model, so I thought hmm, let's try this in my Asus z490 Windows 10 PC. And I got very lucky.Here's a hint: with 2 cards, and 4 NVMe, I get 10,000MB/sSee the attached AS-SSD and CrystalDiskMark NVMe performance image.Without a driver, the 2 NVMe drive show up fine in Windows 10, but to get the Acquantia NIC chip to function you must use the following driver:Driver: Marvell Acquantia AQC107 driver (v2.1.21.0 in my case)Download: Go to Marvell, Support, Ethernet, Driver Download section and download the Win10 driver for part# AQC107Note: Marvell purchased Acquantia recentlyThe card has a PCIE 8-lane interface. The 10gbe NIC would use up 1 to 1.2 of those lanes, leaving 7 lanes or so for the 2 NVMe drives. I am not sure if they are using a PCIE switch to balance that out - which would be the most ideal way to do it. Either way, this is magic. With 2 of these E10M20-T1 cards, I finally have 2 10gbe NICs and 4 Samsung 970 Evo Plus NVMe sticks feeding the CPU via 16 PCIE Gen3.0 lanes (My Samsung 980 Pro NVMe runs off slow PCH lanes for my boot drive).Oh...I bet tis works fine in a supported Synology NAS as well. But do not think that it will work if it is not explicitly supported by your NAS model. Synology explicitly stops (perfect compatible) cards from add too much really cool functionality to their NAS units. And at least as of now Synology does not allow NVMe drives for storage, only for cache for SATA HDD and/or SATA SSD.The card is a work of art. I rarely see this level of quality even at the enterprise level.I am sure this works well in the compatible Synology NAS units - read the compatibility list and don't think it is just a suggestion.I can't say if this will work for you in a Windows 10 setup (know the risk) but I can tell you that it worked for me. The toughest part was figuring out what vendor Synology used for the NIC chip as the NVMe just worked. Once I found that is was Acquantia I had to figure out that Marvell recent purchased them. The driver was sitting there say, download me and go for it - and I did.My NAS setupDS1621xs+ (does not support this E10M20-T1 NIC/NVMe card)OS/DSM 6.2.3-25426 Update 3My Windows 10 x64 setupMotherboard: Asus ROG Strix-E (bought summer of 2020, cheap but effective motherboard, USB 3.1 Gen2x2, but no Thunderbolt)CPU: 10th Gen i9-10900K (stock speed but will do 5.3Ghz, bought summer of 2020)RAM: G.SKILL TridentZ Series 64GB (4 x 16GB) 288-Pin DDR4 SDRAM DDR4 3400 (PC4 27200) Model F4-3400C16Q-64GTZ (running stock at 2133mhz, quite a few years old)PCIE slot usage: Each of the 2 E10M20-T1 [PCIEx8] cards runs in the 2 CPU-wired PCIEx16[physical slots] - so a x8/x8 slot setup (I am a developer, not a gamer)Good luck
済み
Comentado en Japón el 19 de noviembre de 2020
E10M20-T1のSSDキャッシュを使用する場合、SNV3400とSNV3500のみ互換性があります。表記してください。
Productos recomendados
Mex $4,890.60
Mex $ 1,881 .00 Mex $1,881.00
Mex $28,098.29
Mex $ 1,881 .00 Mex $1,881.00
Mex $4,747.64
Mex $ 1,881 .00 Mex $1,881.00
Mex $13,537.71
Mex $ 1,881 .00 Mex $1,881.00
Mex $19,000.00
Mex $ 1,881 .00 Mex $1,881.00
Mex $575.25
Mex $ 264 .00 Mex $264.00