Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Satco Mecanismos interiores con terminal de tornillo - 801477

Envío gratis en pedidos superiores a Mex $600.00

Mex $413.11

Mex $ 227 .00 Mex $227.00

En stock

Acerca de este artículo

  • Satco - Pomo de giro de rango completo de 150 W INT


Satco - KNOB INT de rango completo de 150 W


R.J.
Comentado en los Estados Unidos el 3 de diciembre de 2023
No real wiring knowledge required(UNPLUG THE LAMP FROM THE WALL!!), just reverse how the original was installed and since this switch matched perfectly, installed easily.
Sara
Comentado en los Estados Unidos el 7 de septiembre de 2020
Good replacement for a Restoration Hardware table lamp which had a broken dimmer switch. The lamp had been packed away in a closet for years. I’m glad to have it back in service once again. The switch fit perfectly and the process took about 10 mins.
overhear
Comentado en los Estados Unidos el 3 de agosto de 2018
I bought this gizmo to make my bedside table lamp dimmable so that I could read an ACTUAL BOOK in bed without keeping my partner awake. But because I was installing it in a worklight-style lamp with a hidden socket (see pic), I wasn't 100% sure it would fit correctly. In the end, I got it to work with a little bit of help from my local hardware store.POSITIVES:Works great, and contrary to other posts, dims LEDs. (I'm using an Ecosmart 60w LED light bulb, #A810SS-Q1D-01.)IT DOES WORK, BUT ... a few little things :1) Both screw terminals are on the bottom of the socket, not on the side as on the original socket. That meant that I had to cram the wiring into the socket cap (i.e. the metal piece under the socket). It remains to be seen if this will cause ... god knows what outcome. In the event of calamity I'll update this, assuming my laptop is still operational.2) The switch post and knob are permanently affixed, which may be a problem if it's not a good fit for your fixture or taste (see below).3) The switch post is too thick (5 mm or about .2 inches) to fit into the slot in my lamp. I used a metal file to widen the slot.4) The switch is pretty short (approx. 1/2" long) and plasticky-looking (see pic), which might be a problem in some fixtures and households. I'll be looking for a way to cover or replace the knob.5) As others have noted, be sure to label your wires so you know which one should be attached to the brass vs. silver terminal before you take them off the original switch. I used a sharpie and a small piece of masking tape.GO FOR IT.
Customer
Comentado en los Estados Unidos el 19 de noviembre de 2018
For such a simple device, it appeared to have been assembled with adequate workmanship. I bought it to replace a 3-way socket in a table lamp beside the sofa in our den so that I could dim the lamp while watching TV. It worked well for about 4 months then developed intermittent behavior ... the brightness jumped erratically and would not ramp up/down smoothly as I turned the adjustment knob. I uninstalled it, cleaned the potentiometer with contact cleaner, reinstalled it, and it worked well again for about 1 more month before the symptoms returned. No amount of further cleaning of the control was able to restore proper operation. Conclusion: cheap parts = junk.
Kurt
Comentado en los Estados Unidos el 10 de diciembre de 2017
I just installed this device. It seems fine, controls a 150 watt equivalent. The only thing I'm unhappy about is that the knob that controls brightness is too short for this lamp. The device and lamp must lean because the knob isn't long enough and I can't imagine a fix. It would probably be fine with most lamps and we're going to live with the issue. See attached photos. It would be nice if there were some sort of an extension, the fixture this replaced had such an extension but it was threaded, this knob is just a push on friction fit.
Productos recomendados

Mex $428.00

Mex $ 235 .00 Mex $235.00

5.0
Elegir

Mex $249.00

Mex $ 144 .00 Mex $144.00

4.7
Elegir