No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Dibujo
Profundidad: 400 mm (no incluye asa)
Diseño único que soporta PSU ATX con diferentes tipos de ventiladores de refrigeración
1) Compatible con PSU ATX PS2 con ventilador superior e inferior de 120 mm
2) Compatible con PSU ATX PS2 con ventilador lateral de 80 mm
Filtro de polvo extraíble y reemplazable
Filtro de polvo extraíble y reemplazable
Mohammad Shoarian
Comentado en Canadá el 22 de febrero de 2025
I used a mini-ITX motherboard and plan to install more hard drives inside it later. I replaced the fan with PWM fans to control fan speed and reduce noise.
CL
Comentado en los Estados Unidos el 2 de febrero de 2025
Not a bad case. Fans are a bit loud, but 80mm Noctua's fit fine.
Doug
Comentado en los Estados Unidos el 13 de enero de 2025
Replaced the front fans with 4 BeQuiet 80mm fans, and the unit runs nice and quiet. This is a MATX build with a relatively beefy processor for this case/fans. I used the Intel Ultra 7 265K. I tried the small Noctua NH-L9i-17xx, and it was fine under low loads. However, when I load tested the system, the temps went way too high to fast. I decided to up this to the Noctua NH-L12 Ghost S1 Edition, and this works ok. It is a REALLY tight fit, but with the fins aligned to allow air from the case fans to pass through them from front to rear (tips of the heat pipes touching the side of the case - some heat transfers to the case as well). it cools pretty well. Sustained load testing on all 20 cores for 1 hour hits 102-104 degrees. Going to change the fan to a NF-A9 PWM for higher RPMs/CFM/Airflow, and I think that combination will work better under moderate loads, and still have enough cooling capacity to stay in the 90s under short term heavy loads. If you are putting this case in a data center, you would just beef up the 80mm fans to some high CFM screamers and this case would run cool, but for home lab type use I think this combination of case/fans/coolers is a nice quiet compromise setup that runs well for moderate loads, but will not fry a CPU under short term heavy loads.
WH
Comentado en los Estados Unidos el 31 de diciembre de 2024
I built a custom PC based on Alpine Linux to run my edge router/firewall/VPN device as well as some docker containers for media serving and surveillance recording (Emby and Frigate, respectively). The construction is high quality. I initially had some concerns as it was a bit wobbly sitting out on the table, but once mounted inside the rack there was no sagging or movement at all. I replace the included (very loud) fans with Noctuas and the device is practically silent. The HDDs make the most noise out of everything.One maybe important thing, the case may be too deep for some equipment racks. I have a Tripp Lite 6U rack, and this case sticks out maybe 1-1.5 inches, meaning I would not be able to wall mount the rack. I can live without doing that, though I had planned on doing so in the future at some point. Just pointing this out.
Drknght
Comentado en los Estados Unidos el 30 de noviembre de 2024
Case is great. Looks great in my server rack, great value for the money. Plenty of room for 4+ 3.5HDDs . Using this as an Unraid Server. … great choice
Productos recomendados
Mex $1,005.86
Mex $ 482 .00 Mex $482.00
Mex $5,319.00
Mex $ 1,881 .00 Mex $1,881.00
Mex $1,699.00
Mex $ 815 .00 Mex $815.00
Mex $4,699.00
Mex $ 1,881 .00 Mex $1,881.00
Mex $585.73
Mex $ 316 .00 Mex $316.00
Mex $1,309.00
Mex $ 536 .00 Mex $536.00
Mex $1,049.00
Mex $ 472 .00 Mex $472.00
Mex $596.36
Mex $ 322 .00 Mex $322.00