No hay artículos en el carro
No hay artículos en el carroRackChoice 2U Micro ATX Compact Rackmount 2 x 5.25 chasis compatible con PSU ATX PS2 con ventilador de 120 mm en la parte superior
Nato
Comentado en los Estados Unidos el 28 de febrero de 2025
I am giving this 5 stars due to the build quality and the price. That is not to say its not without its flaws, but these are not issues I had to deal with in my build.Good: Price! Quality Build.Cons: A couple of gripes, but any of the changes I would recommended would likely drive the price up beyond its sub $100 price point.Gripe 1.) There are two, 80mm fans at the front. These use Molex adapters (Blah!). I already planned on replacing these with a pair of Artic or Noctua fans for better performance.The location of these fans make it impossible to service them without taking the system apart. They sit between the front vent and the HDD Trays, but tucked under a lip of the front of the case. So to get access to the fans, you would need to remove the Hard DrivesGripe 2.) Same thing with the filter, it is tucked away in an out-of-reach place. My simple fix for this was to remove the foam filter and set it on the outside. The airflow holds it in place but I am going to 3D print a bracket with magnets to keep it there.Meh 3.) Less of a but something to be aware of. The front HDD Trays: This is a shorter chassis (What I wanted) but if you are planning on installing full size HHDs in the Trays, you will have almost zero tolerance between the SATA/Power connectors and your Motherboard. Its VERY tight. If you are going to use SSD's this may not be as big an issue. And if you are like me and not planning on using the trays at all, then hey no issues.I plan on using a couple of 5.25 bay HotSwap HHD Trays from Icy Dock, and there is plenty of room behind those and the Power Supply.Overall, great Case!Pictures:Red Arrow points to where the filter is located between the front and fans. Have to remove HDD Cage as well as Fan Assembly to access Filter, so it was relocated to the outside of the case (Also pictured).Also showing HDD / SSD Clearance.
Dave M
Comentado en Canadá el 26 de agosto de 2024
Some sharp edges but otherwise some good tolerances. Bought a couple hot swap 2.5" bays to make this a 12 drive beast of a 2U unit. Decent airflow. Make sure you get a good quality low profile cooler. Space for a full size ATX PSU is a nice option. Swapped the fans for Noctuas, the included fans are a bit cheap and noisy. Once all together, a nice quiet low profile case.
JTH
Comentado en México el 5 de diciembre de 2024
buen producto, buen precio
Justin Taylor
Comentado en los Estados Unidos el 16 de septiembre de 2024
Pros: vents on top for power supply, racks well if you stack it on another server that's racked in with rails, decent build qualitycons:not much room, I'm currently doing this one with 6 SSDs and it's a little cramped with all the wiring.If you're using more than a single large spinning drive, i wouldn't recommend this chassis.Default fans are kinda cheap, buy 2 80mm Noctua fans they're much quieterhard drive mounts are really built for larger spinning drives, SSDs don't have much mounting options outside of just laying them inside the chassis somewhere
Jaime
Comentado en Canadá el 7 de noviembre de 2023
The case is solid, comes with all the screws you'll need for a motherboard and PSU. Fits 4 HDDs comfortably. The handles are solid and fits well in a standard rack.The first change I made was replaced the two 80mm fans with Noctua ones, it made a huge difference. Also the power LED is extremely bright - you cannot look directly at it. I put a 5.1k resistor on that wire to reduce the brightness.
Omar
Comentado en México el 24 de noviembre de 2023
Los puertos frontales USB a veces no hacen bien contacto, dependiendo si es Memoria o el Cable del teléfono.
dowNNshift
Comentado en los Estados Unidos el 2 de septiembre de 2023
I've been really impressed with this little server case. I installed an AMD based mini-ITX motherboard and SFX power supply with an ATX adapter frame. With higher quality fans, it runs quietly and met the need as a laboratory based server for running precision fiber optic microscopes and other Windows-based tools.The chassis is made of decent quality and can adapt easily to whatever custom need you have. Makes for a great media, industrial, or general purpose server. You have room for several SSDs and low profile expansion cards. I'll definitely buy again for future projects.
Productos recomendados
Mex $2,199.00
Mex $ 879 .00 Mex $879.00
Kepuch Silklike Funda para Honor X9b - Case Carcasa Placa de Metal Incorporada para Honor X9b - Gris
Mex $199.96
Mex $ 109 .00 Mex $109.00
Mex $1,089.00
Mex $ 577 .00 Mex $577.00
Mex $1,385.21
Mex $ 581 .00 Mex $581.00
Mex $1,523.00
Mex $ 624 .00 Mex $624.00