No hay artículos en el carro
No hay artículos en el carroMás información del producto
Osvaldo Martinez
Comentado en México el 4 de febrero de 2021
Tal y como se describe en la publicación. Fácil de instalar y queda perfecto en el vehículo
Burt & Marlene Ahrens
Comentado en Canadá el 21 de septiembre de 2021
This tail gate lock fit my 2013 Rigdeline perfectly. After watching a video on installation and going two washers a little, it could be installed easily in about 45 minutes. If I can do it ,anybody can!!
Uncle Q
Comentado en los Estados Unidos el 27 de agosto de 2019
This works very well, and was reasonably easy to install on my 2013 Honda Ridgeline, which has the factory camera in the tailgate handle. The included instructions were not the best, but I found the video to be excellent, and used it during the install. You just need to refer to the instructions a to locate the proper drill bit and torex sizes.The locking mechanism integrates well internally, locking and unlocking both tailgate handles with a single key. The keyhole is integrated in a smart little unit that tucks perfectly under the tailgate handle, and is small enough that it really isn't in the way - the tailgate is easy to open.The action of the key is somewhat asymetric, with a clockwise rotation of about 90 degrees being sufficient to engage the lock. Disengaging only takes about a forty five degree rotation counterclockwise.
Django
Comentado en Canadá el 20 de septiembre de 2017
Works great. Easy Install. Keeps my tailgate secure and the contents secure when I lock the tonneau cover also. I have a black Ridgeline and the black lock looks like it came from the factory.
Customer
Comentado en Canadá el 18 de abril de 2016
Worked as it said and very easy to install yourself if you have any knowledge of tools at all. Key seems a little stiff to turn this is why i only give 4 stars
Watson
Comentado en los Estados Unidos el 6 de enero de 2015
This is a well constructed product that works very well in the Honda Ridgeline. The major components of the lock are of a quality heavy gauge metal that would not break unless unless the door was disassembled. There are exterior plastic components and if someone were to take a hammer to these components, I'm sure they could destroy them, but it is unlikely that they would be able to unlock the door. Frankly, if someone were to take a hammer to my truck, I would rather that the outer components break off than remain intact and possibly cause further damage to the body of the tailgate. There are some challenges with the installation of this lock, however. My suggestions are as follows: On Step 1, after the top panel of the tailgate has been removed, take a picture of the orientation of the white clips. They basically all go the same direction. You remove the clips from the tailgate and replace them in the plastic top panel that you have removed from the tailgate. The panel snaps back into the tailgate during reassembly. In Step 2, you will have to file the washers on both of the screws holding the factory handle in place. This is not hard, but it is nice to know about it in advance as other reviewers of this lock have noted. Don't worry about weakening the washer, as the bracket is more than strong enough to make up for any change in the washer. In Step 3, you are drilling through plastic and it is very helpful to have a shop vac around to pick up the plastic drill fragments. They could jam up the lock in the future if you don't remove them. The drilling is very easy to do. In Step 5, the orientation of this picture is 180 degrees rotated from the other pictures. Now comes the really tricky part that takes a bit of a touch. I had to file parts of the crank rod slot (and the tab that it fits over) very slightly to get this lock to work really well. Don't even try to do this unless you have a real feel for mechanical parts/mechanisms as you could easily overdo it (and then you are faced with ordering another crank rod from the manufacturer). I may have just gotten a set that came a little "tight" and your installation may go perfectly without any of these adjustments. I would be really interested to hear if any other reviewers had this problem.
Productos recomendados
Mex $1,015.42
Mex $ 487 .00 Mex $487.00
Mex $298.61
Mex $ 149 .00 Mex $149.00