Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Paquete de 15 conectores de cinta LED erless con cable de 33 pies, aprieta los bloques de terminales de tornillo de 2 pines y conector de 10 mm con cable de destornillador a conector de tira

Envío gratis en pedidos superiores a Mex $600.00

Mex $250.00

Mex $ 127 .00 Mex $127.00

En stock

1.Tamaño:2p-8mm


Acerca de este artículo

  • El conector de tira de luz LED cuenta con un diseño mecánico único tipo de fijación de tornillo que funciona bien en la conexión de tira. No necesita soldadura tediosa, se utiliza rápida y fácilmente para conectar la cinta LED al cable. Estos conectores son adecuados para tira impermeable LED IP65 de 2 pines de 8 mm y tira no impermeable, tira COB.
  • Cómo conectar: estos conectores LED de 2 pines no tienen soldadura. Simplemente gira los tornillos, coloca la cinta LED y el alambre, asegura la cinta LED y el cable para estar seguro.
  • Estos conectores de tira de luz LED soportan hasta 6 A de corriente y son compatibles con 5 V, 12 V, 24 V y 2 pines, te permiten conectar tiras LED más largas por un conector LED
  • Aplicación: estos conectores LED son adecuados para proyectos LED como proyectos de iluminación de clóset, gabinete, fondo de TV y otros.
  • El paquete incluye: 15 conectores + cable de 32.4 pies + 1 destornillador



Descripción del producto

Paquete de 15 conectores de luz de cinta LED sin erless con cable de 33 pies
Apriete los bloques de terminales de tornillo 2 pines 8 mm conector / 2 pines 10 mm conector
Conector de 2 pines de 8 mm con cable de destornillador a conector de tira para tira LED decorativa de 5-24 V

 Conector de 2 pines con cable de destornillador a conector de tira para tira LED decorativa de 5-24 V

Adecuado para gabinetes

 Conector de 2 pines con cable de destornillador a conector de tira para tira LED decorativa de 5-24 V

Adecuado para estudio

 Conector de 2 pines con cable de destornillador a conector de tira para tira LED decorativa de 5-24 V

Apto para cocina

 Conector de 2 pines con cable de destornillador a conector de tira para tira LED decorativa de 5-24 V

Adecuado para escaleras


Gracefully Gleaning
Comentado en los Estados Unidos el 25 de enero de 2025
Bought this to run some led lighting in some shelves I’m making. Using Tatazone COB led strip lights. Haven’t installed yet but tested lights and they work great so I’m confident with the splicing should be fine.
Blessed by Jesus
Comentado en los Estados Unidos el 13 de abril de 2025
My son installed under the cabinet lights for me in the kitchen. Came out so nice and no more cooking in the dark!
Hodgepodgerama
Comentado en los Estados Unidos el 22 de julio de 2024
I bought 2 sets of 10mm LED lights from one of the local lumber stores. They used 4-wires and a bunch of complicated connectors. I put the first strip up and tested it and it was green. So I punted and started over with 8mm warm white lights from Amazon. SO MUCH SIMPLER because there are only 2 connectors. These block connectors are super easy to use and you can actually tug on the wires to make sure they are secure. I used the wire in the wall and in the attic (inside a blue nerf-tube) to run power over to the cabninets on the other side of the klitchen. Smaller wire means smaller holes in the cabinets, whihc is a huge plus. I recommend these to anyone with a mored advance undercabinet lighting layout .
Experimental
Comentado en los Estados Unidos el 5 de mayo de 2024
With a COB led strip you will most likely have to shave some material from the end of the strip to lower the profile to accommodate the connector. This isn't a big issue but should be noted.I should point out that the wire is 22 AWG which isn't the best for long runs. The added resistance may effect the light output if one was to use the most of the roll to go from the power source to the lights.I did find that the connector blocks worked reasonably well once the end of the LED strip was shaved down to fit the strip end.It should be pointed out that these connecters are designed to only accept one end of a light strip. The other end is designed strictly for connecting wires. There are far better connectors available for spicing two sections of LED strips together.
Fastle
Comentado en los Estados Unidos el 26 de noviembre de 2024
This helped bridge some lights for a big gap in kitchen cabinets. I was able to hide the wire with a stick of trim.Easy to use, connectors work easy and all hardware needed was included. I have wire left for more projects.Just as described, no issues. (Using a 2 pin) when i run out I'll buy again.
Productos recomendados

Mex $171.29

Mex $ 94 .00 Mex $94.00

4.3
Elegir