No hay artículos en el carro
No hay artículos en el carroDescripción del producto
-
13 Casquillos
2,19”, 2,50”, 2,63”, 2,78”, 2,83”, 2,83”, 2,87”, 2,90”, 2,94”, 3,05”, 3,20”, 3,29”, 3,47” DE
-
4 Mangas
3″ O.D. × 2.53″ Long
3.25″ O.D. × 2.53″ Long
3.63″ O.D. × 2.53″ Long
4″ O.D. × 2.53″ Long
-
2 Placas de Manga
3,25 ″ de diámetro exterior. × Paso de 2,72 ″
4″ de diámetro exterior. × Paso de 3,2 ″
-
2 Tornillos
7.5 ″ de Largo × 0,75 ″ de Diámetro.
-
1 Nuez
3″ de Largo × 0,75″ de Diámetro.
Tornillos Deslizantes Dobles
Dos tornillos deslizantes de grado 8,8 proporcionan un par de torsión máximo para garantizar un funcionamiento rápido y sencillo, mientras que su roscado de precisión evita cualquier deslizamiento mientras trabaja.
-
Extracción de Cojinetes
-
Instalación Rodamientos
Drake the snake
Comentado en los Estados Unidos el 5 de marzo de 2025
Replaced the front wheel bearings and hubs on my xb. I was kinda freaking out cause ive never replaced pressed in bearings before. This kit works awesome! Cannot remove hubs with this kit, but they are easy to pound out with a large socket and hammer. Removes and installs the bearings with ease. Installs the new hub with ease. I greased up the bolt and used an electric impact to do the heavy work. This kit is worth every penny and saved me a bunch of time. For the money I saved doing this myself, the kit is payed for, and I'm sure I will get many more bearings in and out with this product
Chris Bryant
Comentado en el Reino Unido el 11 de agosto de 2024
Needed to press out 2 very old bearings and press in new ones and hub.Never quite know how a purchase will turn out.This press was insanely good.Literally earned its money on the first bearing. Second one was a bonus.Very easy to use. Lots of sleeves and plates to choose from.Honestly blew my mind how well this worked.
Erick76
Comentado en México el 21 de julio de 2024
Justo lo que venden y además son muy buena calidad.
D
Comentado en Canadá el 16 de mayo de 2023
first off the product is well constructed.hints:make sure you use the correct ring when pulling out the bearing.do not use an undersized one as it will try to seat into the inside of the hub where the bearing is.for the inside ring use the correct size to not damage the speed sensor(if you didn't take it out beforehand--they rust in place and break if you try to get them out.to reinstall the bearing place it in the freezer overnight and grease the inner hub.before that remove all rust from snap ring channel and the lip where the bearing will seat against.make sure you use the correct inner ring--too big will break the speed sensor and too small will pop the inner bearing race out and make the hub flop around.finally,if the outboard race sticks to the hub,and you want to reuse the hub,use a dremel to cut a channel into the race.then heat the race up with a torch.finally,using a hammer and chisel,split the race(it will crack) so it will easily slide off the hub.
Alejandro a.
Comentado en México el 12 de marzo de 2023
Buenísima herramienta para extracción e instalación de baleros de rodamiento me gustó me facilita el trabajo en la mecánica
Cliente de
Comentado en México el 23 de agosto de 2022
Buena relación precio y calidad y las facilidades de pago son una buena oportunidad de compra
eduardo
Comentado en México el 29 de abril de 2022
Muy útil herramienta, se ve resistente y el precio muy accesible
Jesus lopez
Comentado en México el 28 de agosto de 2021
Excelente producto, los materiales son de buena calidad, buen precio y funciona correctamente en la practica
Isaí García
Comentado en México el 3 de marzo de 2021
Un kit de herramienta increíble nos ha sacado de muchos apuros increíble como ayuda en toda instalación de baleros
Adrian Hernandez
Comentado en México el 20 de septiembre de 2021
Si sabes como usarlos son bastante útiles. No apto para princess.
Denisse Ruiz
Comentado en México el 27 de octubre de 2020
No se pudo cargar el contenido.
John Jordan
Comentado en Canadá el 10 de enero de 2020
Quality of tool is outstanding for the price. Effortlessly pressed out rear wheel bearings on Audi A4 B5 and then pressed new bearings and hub back in. Comes in sturdy case. Those damaged in transit must have had a heck of a journey to the buyer. Lots of different plates, so will no doubt find a use for it again. Mine did come with instructions, but the instructions didn't match any of the engraved plate identifiers in the kit. Wasn't terrible to figure out, but would have gone quicker with proper numbers to get the set up right the first time. Very impressed over all. The bolt to wind the bearings out and in didn't show a scratch at end of the job, but I had followed instruction and slathered it with grease first, which I'm sure helped.
Grant T McLaughlin
Comentado en los Estados Unidos el 28 de febrero de 2018
This is a well-made, versatile set of wheel bearing bushings, adapters, and pressing tool that I got for about $30 less than a similar set I was considering from a discount tool retailer whose initials are "HF." I immediately put this set to work to press in a new front wheel bearing on a 2008 Honda Ridgeline. I first had to press the bearing into the steering knuckle, followed by pressing the wheel hub into the bearing. This set worked great and made the job easy!All of the components in the set appeared to be well finished and shipped with a protective layer of oil to avoid rust. The blow molded case is convenient and sturdy, and the tool components fit well in their designated slots.I also wanted to make a couple of points about issues other reviewers raised with this set:1) Using the tool to press in a bearing ruined the threads on the screw -- The key to avoiding this problem is to lube the heck out of the screw each time you use it. I took no chances and used a generous amount of general purpose grease to lubricate the screw, and it showed no damage after the two pressing operations I described above.2) The adapters and bushings have numbers instead of diameters stamped on them, making it more awkward to figure out what sizes you need for your particular vehicle -- This set comes with a small booklet provides instructions and diagrams for using it on common brands of vehicles. The diagrams include call-outs showing the bushing and adapter numbers you should use, which you can cross-reference with a diagram and parts list for the set on the last page of the booklet. This makes it easy to quickly pick out the right mix of bushings and adapters for your vehicle, and I don't feel it takes any longer than measuring and matching up diameters on your bearing and tool.
Productos recomendados
Mex $3,717.85
Mex $ 1,747 .00 Mex $1,747.00
Mex $233.00
Mex $ 139 .00 Mex $139.00
Mex $295.00
Mex $ 150 .00 Mex $150.00