No hay artículos en el carro
No hay artículos en el carroMolex 11-03-0044 Accesorios para conectores, herramienta de extracción Mini-Fit Jr. Para la extracción de la serie de terminales engarzados mini-fit jr.Tm de sus alojamientos. Herramienta de fácil extracción. Tipo de producto: accesorios de conector. Las especificaciones de engarce de herramientas Molex solo son válidas cuando se usan con terminales Molex y herramientas fabricadas por Molex y vendidas por Molex o distribuidores autorizados ("Herramientas Molex"). Cuando se utilizan herramientas distintas de Molex Tool con sistemas de conectores específicos de Molex enumerados en nuestros documentos ATS, la calificación de herramientas de Molex no se aplica y la responsabilidad de la calificación completa del sistema de conectores es la del cliente. Molex no asume ninguna responsabilidad por el rendimiento del conector o el soporte de herramientas cuando se utilizan herramientas distintas de Molex Tooling o cuando se modifica Molex Tooling. Documentos de la herramienta de aplicación: ATS-011030044, TM-638000029, TM-638000029CN, TM-638000029DE, TM-638000029FR, TM-638000029IT, TM-638000029Jp. 638000029SK, TM-638000029SP, TM-638000029TH, TM-638000029TW, TM-638000029VN
YKK
Comentado en los Estados Unidos el 20 de diciembre de 2024
If use use Molex mini-fit connectors you'll eventually need one of these. Works fine to extract a pin or socket from the connector housing. Makeshift solution (tweezers etc.) will likely fail and just damage the connector. This is the right tool for the job.
John
Comentado en Canadá el 3 de noviembre de 2023
Bought this for a project and never used it. Kept it anyway for future use. Very well made.
H. Poling
Comentado en los Estados Unidos el 13 de abril de 2022
I had a little computer build that required reworking the fixed cables on a basic power supply. I wanted to salvage some wires from old parts and decided to buy this "official" Molex tool since the pins are tiny and have limited clearance to the retaining tabs. The tool worked fine for emptying a 24 pin motherboard block and some others. Other reviewers reported problems with this tool, I think my success is based on a couple of subtle points:a) make sure the prongs go into the little slots alongside the female socketb) the prongs have to go in until the hilt of the tool touches the plastic connector blockc) wiggling the tool slightly as you push it it and when it seats helps work the prongs to release. Note I wrote, "slightly".d) the connector (and I suspect this may be where others were disappointed) should also be pushed forward/in to help release the retaining prongs. (As the tool goes in, it pushed the connector back, jamming the retainer tabs against the end wall of the slots. Working the pin forward frees the tabs to flex.)e) If you do all the above to free the connector, it may simply take a little more pull to get it out. For me, some came out freely and some required a tug. But beware to wiggle the tool a little between test-tugs and make sure the tool is fully inserted.After reworking these cables, I found a single prong of this tool was right for releasing the single-side retainers on the small 3/4 pin connectors used for PC cooling fans. A handy bonus use!After this, my tool is in fine shape for future projects.
Richard S. Bates
Comentado en Australia el 12 de septiembre de 2021
I bent the pins almost immediately. Tool just didn't seem to go deep enough to unclip the retaining clips on the pins. So didn't work on the non OEM Molex plugs on the SATA cables I was trying to re-pin. Got the job done with 1c staples.
A. Kent
Comentado en Canadá el 8 de mayo de 2019
Don't waste your money on cheaper alternatives. Instead of replacing cheap alternatives half way through a job because they broke or just don't work anymore, buy this once and you're set. Pops out the connectors first time with minimal force and doesn't mangle them so badly that you can't get them back in.
Productos recomendados
Mex $634.66
Mex $ 285 .00 Mex $285.00
Glarks SN-28B - Herramienta profesional para prensar pines de 2,54 mm, 3,96 mm, 28-18AWG 0,1-1,0 mm2
Mex $349.00
Mex $ 164 .00 Mex $164.00
Mex $375.64
Mex $ 191 .00 Mex $191.00