No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Tamaños para pinza: 1 mm/1,6 mm/2,4 mm/3,2 mm. Su cabeza es de 4 garras, y los accesorios de sujeción son más estables.
8 pinzas de acero están hechas de acero inoxidable, esta tuerca de sujeción está hecha de aleación de zinc.
Cambia rápidamente la capacidad de sujeción del molinillo eléctrico y resuelve la zona ciega del camino de sujeción.
Steffen Schneider
Comentado en Alemania el 7 de junio de 2024
Mein Schnellspannfutter von Dremel (aus Aluminium) ist gebrochen, daher brauchte ich ein Neues. Ich wollte mir etwas Höherwertiges als Aluminium holen, hat Dremel aber leider nicht. Daher holte ich mir dieses Set, Lieferung dauerte etwas länger, aber das Spannfutter ist sehr gut. Es entsteht keine Unwucht und hält das Werkzeug sehr fest (denke auch etwas fester als die Dremel Backen). Wer ein höherwertiges Backenfutter sucht, ist hier richtig, ich bin sehr zufrieden. Getestet habe ich es mit einem Dremel 8200.
Ramses Osirus
Comentado en los Estados Unidos el 2 de junio de 2024
A few reviews said they didn't fit on their Dremel brand rotary tool, but they work just fine on mine. Much cheaper than the name brand ones too. Held my smaller diameter bits in place.
Hank Hirst
Comentado en los Estados Unidos el 28 de mayo de 2024
fits both my 3000 and 4000 and gives me the ability to use a wide variety of bits.
I'mNoHoople
Comentado en los Estados Unidos el 19 de marzo de 2024
Using a Dremel is always great fun, but not so much the different size collets needed to support the bit shafts. Having these collets all in one place and all different sizes makes it so much easier to work. Before, if I used a buffing bit, I would have to tape the shaft to make it fit. Gratefully, now that's no longer the case. Great set for the money.
MW
Comentado en el Reino Unido el 14 de diciembre de 2024
Completely useless! Check out the photos (these show the two 1mm collets close up, one of the 2.4mm collets (the edge obscured by the 1mm drill (see fourth photo to understand)), and the whole set with a 1mm drill across the top and a ruler for reference). See how off centre the holes are for the two 1mm collets? And it matters, putting a 1mm bit in to these, tightening and rotating, the tip of the bit describes a tiny circle, it's awful! It's obviously harder to see how well centred the larger ones are, but it's clear that one of the 2.4mm collets (third photo) looks a bit squashed, not sure if this is bad engineering or post manufacture damage.Additionally the length of the collet that grips the bit is very very short, I actually initially thought this was the whole problem (a short grip, like a pincer, means it's possible for the bit to have lateral play or be set off centre easily) until I took close up images and could see the collets properly. The grip seems less than 1mm long though it's hard to see since it's internal; I couldn't measure it accurately without breaking off one of the claws, which I'm not going to do as I will be returning the product.Finally, it's clear that the product photos are clean and precise, and clearly are not photos of what I've had delivered.
Productos recomendados
Mex $951.00
Mex $ 504 .00 Mex $504.00
Spring Collet, Collet Chuck Instalación Fácil Sujeción Firme ER32 para Centro de Mecanizado (D=26mm)
Mex $251.00
Mex $ 133 .00 Mex $133.00
Mex $256.00
Mex $ 140 .00 Mex $140.00
Mex $440.00
Mex $ 211 .00 Mex $211.00
Mex $413.74
Mex $ 223 .00 Mex $223.00
Mex $208.82
Mex $ 125 .00 Mex $125.00
Mex $4,020.98
Mex $ 1,648 .00 Mex $1,648.00