Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

L8 Grabador láser, cortador láser de salida de potencia de 40 W, carcasa acrílica integrada con ventilación, máquina de grabado láser todo en uno, bomba de asistencia de aire, panal, cámara,

Envío gratis en pedidos superiores a Mex $600.00

Mex $24,801.75

Mex $ 1,881 .00 Mex $1,881.00

En stock

1.Nombredelestilo:40 W


  • Velocidad de grabado inigualable de 40000mm/s: gracias a la última tecnología láser y a la estructura de la máquina resistente, esta máquina alcanza un rendimiento ultrarrápido. Rompiendo el límite de velocidad de las máquinas de marco tradicionales, esta máquina es tan rápida como la mayoría de las máquinas láser Galvo pequeñas, superando a otras máquinas láser de diodo en el mercado en más del 33%.
  • Salida de potencia óptica de 40 W (40000 mW): Siente la potencia de la capacidad de Genmitsu L8 para cortar materiales como madera contrachapada de tilo de 20 mm, acrílico negro de 12 mm e incluso acero inoxidable de 0,05 mm en una sola pasada. Con la bomba de asistencia de aire inteligente de 30 l/min incluida y panal integrado, puedes esperar un corte súper eficiente y claro cada vez.
  • Solución todo en uno: totalmente montada y lista para salir de la caja con un escudo láser acrílico de escape de ángulo visual de 360°, el L8 es tan práctico como versátil. Con accesorios de diseño opcionales, como un purificador de humo y un rodillo giratorio, puede personalizar para adaptarse a su escenario de uso personal.
  • Di adiós a múltiples pruebas y errores: equipado con una cámara compatible con Lightburn posicionar tu proyecto es muy sencillo. Además, con una barra indicadora de alimentación, luz informadora de fallas y detección de flujo de aire, esta máquina le pone en control.
  • Certificado de seguridad láser de clase 1: cuenta con parada automática inclinada, zumbador de monitor de llama activo, un juego completo de interruptores de límite de protección de posición, parada de emergencia, bloqueo de seguridad para niños, te recuperamos utilizando esta máquina de alta potencia de forma segura.



Descripción del producto

El video muestra el producto en uso.El video te guía a través de la configuración del producto.El video compara varios productos.El video muestra el desempaque del producto.
L8-40W
  • De hecho, nuestras mejoras en la placa base y el marco han dado como resultado una velocidad máxima de funcionamiento de 40.000 mm/min. Sin embargo, para el grabado real, recomendamos ajustar la velocidad de acuerdo con el material específico y el efecto deseado.

  • Los accesorios estándar incluidos son: Placa de panal, bomba de aire, carcasa integrada de una pieza con ventilador de ventilación. Los accesorios opcionales incluyen: Purificador de aire, rodillos giratorios y otros módulos láser únicos que se desarrollarán pronto en el futuro

  • Sí, el L8 es totalmente compatible con Lightburn, el sistema de soporte incluye Windows/MAC/Android/IOS.

  • Puedes utilizar la cámara para colocar tu producto a través de LightBurn. Se recomienda importar parámetros preestablecidos para calibrar la cámara antes de usar. Puedes encontrar fácilmente las instrucciones detalladas en nuestros documentos de ayuda del sitio web


Christopher T.
Comentado en los Estados Unidos el 21 de julio de 2024
I bought this 40w laser to replace my couple year old 10w laser and wow, what a difference in quality! While my first laser was great for learning on and such, it doesn't hold a candle to this behemoth.With the enclosure, not having to wear those glasses anymore is fantastic. The camera can use some adjustments, but is still better for lining stuff up than no camera. It definitely speeds up the process of setting up. Having air assist is a must! It makes my projects come out so much cleaner. Performance wise, it's fast. With four times the laser as my old one, it breezes through stuff that used to take me much longer, or not able to even handle at all. So far, I've cut and engraved wood, leather, and acrylic all with great success.The only issue I've had with it is that on a rare occasion, the cable that attaches to the laser can get in the way of the wheel and cause it to not move. I haven't looked fully into yet, but I'd assume it's just about moving it slightly so it can't get that close to the wheel. I should also not, that it only happens you are trying to laser the very top center edge of the bed and again rarely happens even then.Overall, I would say price wise, is the best bang for your buck when looking at other comparable models.
@astrophoto_canada
Comentado en Canadá el 2 de diciembre de 2024
This is my first laser engraver, so the learning curve is steep. The instructions are lacking (other than basic set up and information) and requires a lot of searching online. Setup is easy though as its mostly assembled - picking off the protective film over the acrylic was the worst part.Once calibrated and you get a basic understanding of the machine and settings, it produces some very nice work. The freebie coaster shows a cartooned image of me riding my EUC.There are some design flaws that could, and should, be rectified by Genmitsu.1) Protruding screws on the honeycomb rear left rail bracket contacts the roller causing it to bind. Luckily, I had screws that were ~1mm shorter in my parts bin which fixed it.2) Raising the built-in feet for extra clearance (e.g. roller use) causes the laser head to potentially collide with the front left rail honeycomb bracket (which is now floating above the honeycomb). I used a permanent marker to note the height where it would strike the bracket. If it does strike, then the head will not close the limit contact switch (which as bad luck would have it, it did!). Not good!A fix would be for Genmitsu to invert and shorten the 'hook' to prevent it. May try 3D printing a fix.3) There are no grab handles to raise the machine for extra clearance. Instead, you have to grab the sharp wobbly acrylic, which also may stress and fracture it over time. I'm 3D printing handles that can be fastened to the acrylic opposite the rails which is firmer for easy lifting. I'll likely add some trim to the sharp acrylic also.As its raised, laser safety could be an issue as there is now a gap of several centimeters. A sliding piece of acrylic at the front would mitigate the risk somewhat. Due to the size of the machine, I have it in the corner of a corner desk, so the gap is quite visible from the front.Lastly, there is no mention by Amazon or the manufacture that if you want to return the machine, you're on the hook for return charges which could be 30+ days before a refund is issued. I almost sent it back with the irritating flaws, but decided to fix the issues, as it does engrave well. Amazon did confirm they'd reimburse the shipping charges (Prime) over the paltry $3.99 offered automatically. This is potentially misleading, and I'll believe if and when I see it. Buyer beware!
Tanya Ferguson
Comentado en los Estados Unidos el 16 de diciembre de 2024
1) good value...very good. Good size too.2) precise3) easy to set up.4) cuts very well5) totally worth the investment.6) PERFECT for cutting 3mm, 4mm.The cons:1) The smoke removal fan is loud and not that powerful.After hundreds and hundreds of cuts, i am concerned the power is not as good as day 1. I used to be able to cut 3mm ply at 15mm/s at 100%, now after 300 sheets cut i need to cut at about 13mm/s at 100%. Unsure if its air assist is just less powerful (wearing) or if laser is waning.2) Biggest con: There is a stupid indicator telling you that you have proper air assist on. If you start the machine with air on, it will show red. so turn off machine, turn off air assist. start machine. turn on air assist. light is green. but....half the time I forget to turn on the air assist and totally run a whole sheet of ply.3) spot size bigger than comparable co2 machine.4) cutting thicker than 4 or 5mm seems to burn the edges of the board more than you would think. not beautiful brown like 3mm cuts. you get charred black edges.I would buy this machine again. I own a larger co2(60 watt), and this machine is so easy to use i favor it over the larger co2 laser. The spot size is smaller on co2. but the ease of use and convience of this laser is just great.I use lightburn as software, works very well with this laser.
Happy
Comentado en Canadá el 27 de octubre de 2024
No se pudo cargar el contenido.
Shannon Z
Comentado en los Estados Unidos el 12 de octubre de 2024
An awesome machine. Solid built, packaged so well that it is difficult to unpack. Includes everything necessary to get up and running with the exception of a computer. Quiet air pump, cables, and several sample materials included. The only downside is the acrylic enclosure is on the thin side and requires a little care to avoid damage. I had a minor issue with the built in camera connection and contacted support. They were quick to respond and the issue (my error) was resolved. I have engraved wood slices and granite style coasters using Lightburn software. The camera makes positioning the item to be engraved a simple task. A real pleasure to use and as a previous CO2 laser user this diode laser is a far superior design, more accurate, and easier to operate.
Productos recomendados

Mex $636.79

Mex $ 292 .00 Mex $292.00

5.0
Elegir