No hay artículos en el carro
No hay artículos en el carroEstos botones de correa cuentan con una brida ancha para mantener tu correa e instrumento seguros. Reemplaza tus botones estándar para un ajuste aún más apretado, o configura otro instrumento para usar con tu correa de retención Straplok. Disponible en níquel, negro y dorado para que coincida con los acabados de hardware de guitarra más populares.
Customer
Comentado en el Reino Unido el 14 de febrero de 2025
🎸 I bought these as I had used them before and was satisfied with both the construction and the finish. Some cheaper alternatives are noticeably smaller, and from the images, it is clear they would press into the instrument’s surface when fitted, even with the felt protection. That is not the case with these. They cost twice as much, but the secure fit and the fact that they will not damage the instrument make them a far better option. The only drawback is the screw supplied with the gold version—considering the finish, a brass screw would have been more suitable, or at least one with a matching gold finish. It’s a very small point as you cant see the screw very well once installed.🎸 I found the strap button slightly larger than many of the smaller versions available, which makes the strap sit more securely and reduces the chance of it coming loose. Fitting was straightforward, though it requires care, as there are no instructions included. The biggest concern is preventing damage to the finish. Before installation, I checked inside the instrument to confirm that the tail block was thick enough for the screw and correctly positioned. Mine was offset by about 5mm, though not enough to cause a problem.🎸 To install, I marked the desired position and placed a piece of protective tape over it—avoiding clear tape, which can be difficult to remove cleanly and is not robust enough. I drilled a 1mm pilot hole to match the screw’s depth, measured with the button, screw, and felt assembled. This was then widened to 2mm, then 3mm. To prevent the screw from damaging the finish or the centre seam, I drilled the outer layer to 3.2mm to a depth of 2mm. The screw went in smoothly and held securely. The opening in the button is wide enough to accommodate a standard screwdriver head without issue. As mentioned, I have purchased these before and will again. ✔️
Niladri Sekhar Bhattacharjee
Comentado en India el 10 de agosto de 2024
Product was really amazing 🤩
MAES Marc
Comentado en Canadá el 22 de mayo de 2024
Esthétique et solide.du bon matos pour ma gratte !!!
Rawedge
Comentado en Canadá el 9 de marzo de 2024
Very good quality buttons for a fair price.
Jimmy
Comentado en los Estados Unidos el 18 de diciembre de 2021
I leave my straps on my guitars. I use straps with good quality leather ends and prefer rubber washer style strap blocks. These buttons are deep enough to easily accommodate all that material but still don't look too big or gaudy on the guitar. Made well in the USA and very sturdy.Note: If your screwdriver is meeting a lot of resistance, get the drill out. There are so many reviews on items like this (strap pins, string trees, etc) where folks are complaining about snapped screw heads. Guitar wood is not Ikea wood. Don't be lazy. Drill pilot holes. Considering you can buy a cheap-a** drill for about the price of these strap pins, there's really no excuse not to. Yes, some screws are cheap and flimsy, but even the best hardware will be tested if you try to screw it directly into a piece of rock maple.
Productos recomendados
Mex $218.15
Mex $ 122 .00 Mex $122.00
Mex $801.43
Mex $ 368 .00 Mex $368.00
Mex $1,588.63
Mex $ 762 .00 Mex $762.00
Mex $584.60
Mex $ 268 .00 Mex $268.00
Mex $224.00
Mex $ 112 .00 Mex $112.00