No hay artículos en el carro
No hay artículos en el carroMás información del producto
Sobre nosotros
A lo largo de nuestra larga historia, llena de diversión de 75 años, nunca nos hemos tomado un descanso de ofrecer frescura al mundo. La mayoría nos conoce por el enfriador Playmate, también conocido como "America's Lunchbox", hemos diseñado en 1971 que tiene un diseño tan distinto e innovador, que se exhibe en el Smithsonian. A través de muchas otras innovaciones a lo largo de las décadas, el enfriador de plástico en los años 60, el enfriador de ruedas (1994), los enfriadores duros hechos de plástico (2021) y mucho más en el medio, Igloo se convirtió en la marca para los consumidores que trabajan duro y juegan más duro. No nos detenga Seguimos haciendo todo lo posible en diversión, más rendimiento. Productos construidos para superar las necesidades y aumentar la comodidad de los excursionistas, campistas, pícnicers, padres, atletas, trabajadores de primera línea, guerreros corporativos,
Juan Carlos González López
Comentado en México el 6 de enero de 2025
Funciona perfecto, mejoró la precisión de los pasos del motor del extrusor.
Pearlie
Comentado en los Estados Unidos el 29 de agosto de 2024
I use this at work daily as my lunchbox/man purse. I work outside in the elements often during emergencies, so it allows me to carry a lot of things i may need throughout the day. Zippers seem a little delicate, so i treat them with respect. Keeps my drinks ice cold. After workin in the 100°+ summer heat, ice packs are still frozen at the end of the day. So it's pretty nice. There are cheaper ones out there, but i don't regret paying a little extra for a brand i have trusted my whole life.
Bien
Comentado en México el 26 de agosto de 2024
Todavía no la uso pero se ve muy bien 👍
Darrell L.
Comentado en Canadá el 28 de noviembre de 2024
I had high hopes for this direct drive update for my venerable Ender 3.The kit installation was super easy and quick. Instruction sheet that comes with the kit isclear & and to the point. No issues there.Issues do arise however once the kit is installed and you try to load filament into the extruderassembly; you simply can't... the filament doesn't have a straight path follow from the top entrypoint and through the gears that grab the filament.I took apart the extruder to see what was going on and noticed that the interior filament pathwasn't straight (or clear) for starters. After clearing out the factory malformed holes in the filament'spathway, I could feed filament through the extruder assembly and onwards to the hotend.Once up and running however, things improve greatly. Loading the filament is now much easier andit flows very well out of the hotend's nozzle. Extruder tension adjustment is finicky at best and doesn'treally do much to change the amount of pressure placed upon the dual gear grip/drive setup as theextruder housing is a rather flimsy plastic that bows when the tension screw/spring combination isadjusted.All in all, it had so much potential to be a really great upgrade but in Creality's usual fashion, lackof paying attention to detail(s) and an blatant disregard for Quality Control practices arise onceagain to "bite" the customer leaving them to solve whatever nonsensical idiosyncrasies show up.A 2-star rating at this point is generous considering the amount of time that I had to spendto get this "upgrade" up and running.Caveat Emptor.
SkyeRangerDelta
Comentado en los Estados Unidos el 27 de noviembre de 2024
I had been debating installing this onto my CR-10S for some time and trying to decide between it and something 3rd party such as a Micro-Swiss. This is cheaper and does the job perfectly. Installation was a breeze.I'll note that you should pay special attention to the length instructions/setup for the tubing between the extruder and the hotend; if it's not too length, the filament sometimes likes to push the tubing out of the extruder so get it right.Additionally, if you're using the filament sensor, you'll need to find a way to mount that to the machine again since this moves the extruder off it's original spot (obviously). At present, I just have it hanging freely off the filament since it's light enough to do that but you may want a more permanent solution to this.
Jaydon Sensenig
Comentado en Canadá el 1 de noviembre de 2024
Looks cool but works terrible
Daniel Hedden
Comentado en los Estados Unidos el 14 de abril de 2024
Easy to install. But my CR touch was a pain in the butt to try to make work with it. I would suggest going on thing of hers and printing a mount for it if you have a CR touch. I would also print the one with the 2 fans.And I would get another fan.Also , make sure to run fans at one hundred persend , so you don't get he creep. The bowden tube tends to get hot, if not cooled properly you'lla nice loud clicking noise And then your filament goes everywhere once the bowden tubing comes loose from the under side of the extruder since there is no locking nut for that portion of the under side of the extruder. No issues if you do those things it will work fine and perfect 100% of the time! I love this thing! I hate having to use all that stupid bowden tubing all the time... fyi if you have a fillament run out sensor and you are short on bowden tubing and want tonstill print, you can use the fillament run out sensor as a bowden tube splicer! Works 100% awesome. Enjoy!😀
Maripaz Reyes
Comentado en México el 10 de agosto de 2023
Excelente y si cumple con su función
Karla G.
Comentado en México el 4 de diciembre de 2023
Una súper hielera, guarda mucho el frío y le caben muchas cosas, como botellas y latas, además cuenta con muchos compartimentos súper útiles.
Chester Makowski
Comentado en los Estados Unidos el 2 de diciembre de 2023
After modifying my Ender 3 Pro with most of the suggested upgrades and discarding some that were not useful or made it more difficult to use the printer. I use my printer almost daily as I have designed a few products and soon will be marketing them, some of the product require a color change which is difficult with the Bowden Tube extruder on the side, and using the printer over a year now and experiencing the difficulties and print failures i was looking forward to converting the extruder to a direct drive system to rid myself of the Bowden tube failures and to make filament color change easier. The recent last clog of the Bowden tube mad my decision easy, my printing stopped and I ordered the Creality Sprite Extruder Direct Drive Dual Gear Extruder SE Upgrade Kit, and it was the best upgrade choice ever made for my printer. The upgrade was very easy, instructions were easy to follow and it worked as soon as I completed the upgrade. I have now printed over 30 print models without a failure or jam and my top layer have even improved. Since I am a constant tinkerer and a retired scientist my next upgrade will be to enhance my print speed from my now 150mm/sec maybe with a faster hot end that i could also print carbon fiber filamants. Any product suggestions would be welcomes, Chester
YoliC
Comentado en México el 6 de septiembre de 2023
Hace unos años compré una mochila muy parecida de la misma marca y me encantó, pedí esta y es muy buena en cuestión de conservar los alimentos, el espacio es muy bueno, el único detalle es que los cierres son más rígidos y la mochila es dura, pero buena calidad, sin derrames
frank
Comentado en los Estados Unidos el 27 de julio de 2022
ISRAELBAZUA
Comentado en México el 20 de junio de 2022
Buenisima compra , tengo como 2 años con ella y sigue intacta no tira uuna gota de agua .. solo si se acuesta es obvio por el cierre , pero la vd buenisima compra ..mantiene el hielo perfecto
Pedro
Comentado en España el 25 de julio de 2021
Campo y playa
Jose Angel Parra
Comentado en España el 17 de noviembre de 2021
Tengo varias mochilas térmicas y esta me ha sorprendido por lo amplia que es, con diversos bolsillos, cómoda de llevar que parece que no llevases nada a la espalda y hecha de muy buenos materiales
moumou
Comentado en Francia el 12 de noviembre de 2021
tout simplement génial
Productos recomendados
Mex $3,310.00
Mex $ 1,456 .00 Mex $1,456.00