No hay artículos en el carro
No hay artículos en el carroIdeaformer - Placa de construcción PEI negra de doble cara para Bambu Lab X1/X1C/X1E/P1P/P1S/A1, placa de acero de resorte PEI con textura suave flexible de 257 x 257 mm para impresoras 3D Bambu
mj1234
Comentado en Canadá el 5 de marzo de 2025
I've seen a lot of reviews with issues mentioning the adhesion issues on the carbon fiber texture side specifically. I was able to get it working for PLA, have not tried other filaments. After dialing in settings - playing with higher and lower bed temperatures, different inital layer height, speeds and acceleration - I was able to get perfect adhesion, and have the texture appear perfectly on the prints using the following on the bambu A1 with the 0.2mm standard preset:Build plate: Textured PEI (it doesn't work well with the smooth plate/high temp)Initial layer height: 0.1mmInitial layer speed: 20mm/sInitial layer acceleration: 100 mm/s^2For the bed temp:Initial layer bed temp: 65-70 degrees CPost initial layer: 55 degrees COther than that, the plate quality is great, no issues out of the box and it was packaged securely. Hope this helps anyone who may be struggling!
YUUYA11
Comentado en Japón el 15 de enero de 2025
裏表別柄になっておりマグネット対応の機種であれば使える。初めてテクスチャ付きの出力物をだしたら思ったより綺麗でびっくり定着が若干悪くなるので温度を上げるなりして対応する必要があります。写真はankerの3Dプリンターでプレート80℃ノズル260℃/petg追記 少し初期レイヤーの高さを減らすと綺麗に出やすいです。きれいに出る所とクラックが入って模様が出ない場合はノズルの頭が、移動時に触れて剥がれてしまっている可能性があるので初期レイヤー付近の移動速度を落としたりベットの温度を上げると改善します
カスタマー
Comentado en Japón el 3 de noviembre de 2024
Bambu lab A1純正PEIプレートだと底面の食いつきが良すぎて剥離するのが大変なのと造形物底面を毎度ライターで処理するのが手間なためテクスチャードプレートにしようと思い購入。結果から言うとPETGとの相性が悪く絶望的に定着しません、PETGに最適という文言を鵜呑みにしてしまいました。プレート温度100℃、ノズル温度240℃でなんとか着くか?という感じですがその後の積層で糸引きが気になるため仕様を断念。他の材質は使用していないため結果が良ければ再評価します。
SMW
Comentado en Canadá el 25 de abril de 2024
EDIT May 2024:Seller reached out to me and offered a replacement. I agreed and it came within a few days. The replacement works very well. MUST be kept grease and dust-free, like cleaned every use. Also have to slow the first later right down to like 25. 210 hotend and 55 bed seems to be the sweet spot for me. Using Bambu Lab P1S with AMS.The finish is quite lovely, just remember to keep the surface as clean as can be. Seller's response alone is worth me bumping up the star rating. It's good to have a seller stand by their product. The first one must have been a bad production run or something.Terrific idea, and I wish it worked, but it just doesn't. I've done everything the instructions say but can't get anything to stick - using a Bambu Lab P1S with Bambu Lab PLA. I've been 3D printing for 6 years so I don't think it's newbie error.
Roy Stevens
Comentado en el Reino Unido el 29 de julio de 2023
Very pleased with this bed plate works very well on my X1.Only slight thing the printer does not recognise the plate but a minor thing for excellent prints.
Productos recomendados