Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

HERZO - Cubierta de polvo para amoladora angular de 4/4.5/5 pulgadas universal para molienda de superficie (125 mm)

Envío gratis en pedidos superiores a Mex $600.00

Mex $781.31

Mex $ 382 .00 Mex $382.00

En stock

Acerca de este artículo

  • Extracción de polvo de amoladora angular adecuada para la cubierta frontal de la mayoría de amoladoras angulares de 48-51 mm. Se puede instalar en la mayoría de las amoladoras angulares de 5 pulgadas/4.5 pulgadas. El grosor del disco de molienda de diamante no debe ser superior a 25 mm o inferior a 15 mm.
  • Apto para amoladora angular de 48 a 51 mm
  • La cubierta de polvo está diseñada con una cubierta deslizante giratoria, llega fácilmente al borde de la pared al ras y mantiene el polvo alejado.
  • Capucha de succión con abrazadera de ajuste, 4 arandelas de sujeción de grosor de 1,5 a 5,5 mm, fijación de bloqueo
  • Permite la recogida de aplicaciones de molienda de polvo dañinas



Descripción del producto

HERZO 125 mm amoladora angular cubierta de polvo diseñada para dar a los trabajadores su trabajo bajo un ambiente sin polvo. Es fácil de instalar, solo necesitas tomar 1 minuto. Y puede adaptarse a muchos amoladora angular de 115 mm/125 mm en diferentes marcas. Es tu mejor socio en trabajos de molienda y te dará una nueva visión mientras trabajas.

4

Accesorios

1

Llave

Esta llave puede ayudarte a apretar o liberar accesorios de amoladora angular más fácilmente.

2

Pinzas de lavado

Estos 4 accesorios solo se utilizan cuando la cabeza de tu molinillo es más pequeña que el diámetro de nuestro artículo.

3

Adaptador de vacío

Este es el adaptador de goma utilizado para conectar el limpiador de vacío (algunos limpiadores pueden no utilizar este adaptador de modo)

Cómo utilizar

1

Paso 1

Conecte la cabeza de la amoladora con el cuerpo de la cubierta.

2

Paso 2

Bloquea la cubierta a la amoladora angular

3

Paso 3

Conecte la manguera de goma con el adaptador de vacío

4

Paso 4

Conectar con el limpiador de vacío

Mantener lejos el polvo

55

rodrigo duncan
Comentado en México el 6 de marzo de 2025
una porqueriza de productono se adapta correctamente a la amoladora angular.todos los productos chinos vendidos por amazon son de muy mala calidad y deben de ser prohibidos a su venta
M Sims
Comentado en los Estados Unidos el 10 de marzo de 2025
Dog shroud fit great on my Makita that I burnt up and purchased this Milwaukee and still fit, I had to supper glue the end in the shroud because the band clamp quit working, but the super glue did the job. My rigid vacuum sucked the dust great, and used 16 gallon bags to help keep my filter cleaner. Did my whole garage with one disc from Amazon, and filled up 4 vacuum cleaner bags with concrete dust! Shroud work excellently and still cheaper than the one sold at Harbor Freight.
Antonio Lemus
Comentado en México el 27 de abril de 2024
Todo muy bien
SIAMAK ELYASI
Comentado en Canadá el 28 de agosto de 2022
It is a good dust shroud. It do the job as it is design for. However, it does not fit to 1- my grinder, 2- to my shop-vac. I use it to grind the floor of my garage (concrete). I made pieces with 3D printer to adapt it for my tools and it works fine. You may need to make your own pieces to adapt it for your tools. It comes with several extra pieces to connect it to grinder and shop-vac.But those pieces does not work for me. Connecting it to shop-vac was a problem. After connecting to shop-vac, I tape the vacuum hose to the body of the grinder to secure it. It may be a helpful tip. Happy grinding.
Diego Contreras
Comentado en México el 18 de mayo de 2022
A pesar de que en la descripción menciona que es universal, no pude instalarla en mi pulidor marca Milwaukee, por otro lado, sí se pudo instalar en uno marca Dewalt.En general la construcción del accesorio parece rígida y durable a pesar de ser de plástico. Me parece un accesorio algo caro, aunque en realidad casi todas las opciones que encontré en otras marcas tenían costos similares.
Mary Bates
Comentado en Australia el 22 de octubre de 2022
Didn’t fit my 3 different grinders so wasted purchase
ARACELI A.
Comentado en México el 13 de enero de 2022
Muy buen producto
bjbaker
Comentado en los Estados Unidos el 18 de diciembre de 2021
I needed to remove approximately 100 ft.² of tile mortar from a concrete floor in my basement. I purchased this dust shroud and some cheap 4 inch grinding cups from Amazon. I have an older black and decker 4 1/2 inch angle grinder and this shroud worked OK on it. The shroud is relatively simple to use and comes with different shims to achieve a tight fit around the grinders collar. I had some small screws on my grinder that were in the way of the shroud fitting flash, but it worked fine despite this. The only real complaint I have is with the vacuum discharge port and rubber boot.I purchased a 4” to 2-1/2” reducer to hook the grinder to my rigid vacuum but it was not super clear how to hook everything up. I got as tight of a fit on everything as I could and then just taped it all together. The shroud definitely worked to minimize dust during grinding as long as a vacuum was on. Unrelated to the shroud, make sure you buy some type of vacuum bag or special dust filter as dust will quickly clog your vacuum if a regular filter is used without a bag. Also a face respirator is necessary to avoid inhaling silica dust from the mortar.Good shroud, served its purpose. Worth the money if you’re looking for a cheap and quick shroud for a few projects. I wouldn’t recommend this for long term use.
Doug Fox
Comentado en Canadá el 5 de septiembre de 2020
We wanted to apply a penetrating sealant to our basement floor, and had two options: etch the concrete, or grind it. The grinding option was chosen for a couple of reasons. Our first thought was to rent an 11 inch commercial grinder, but we soon discovered that it wouldn't be possible to easily get it down our basement stairs. That left using an angle grinder with shroud and diamond cup wheel. I ordered the Herzo shroud here, and picked up a wheel at Home Depot.Preparing the shroud for use went smoothly until it was time to connect to our Rigid shop vacuum. The vacuum adapter that comes with the unit is a weird size. It might fit some odd sized vacuum hose, but it's nowhere close to fitting a standard 1-1/4 inch hose fitting. I made up an "adapter adapter" out of the barrel of a 60 cc syringe from the vet clinic. It fit over the end of the rubber adapter perfectly and the other end was made to fit the vacuum hose end with some heat and a hose clamp.It took several minutes of use to work out a technique that gave me the finish I wanted, and from that point on, I was off to the races.The edge grinding "door" gave me some grief - it wanted to stick in the edge grinding position, and required removal from the angle grinder to get it to close. When in use, it did a good job of getting up close to the walls, while keeping dust loss to a minimum.The middle sized spacer ring allowed a good tight clamp onto the Ryobi angle grinder.Overall, this is a well made tool, with the exceptions noted above. I'd definitely recommend it. if you can work out a workable vacuum connection.
Productos recomendados

Mex $270.46

Mex $ 151 .00 Mex $151.00

4.5
Elegir

Mex $2,210.07

Mex $ 994 .00 Mex $994.00

5.0
Elegir

Mex $3,729.00

Mex $ 1,566 .00 Mex $1,566.00

4.5
Elegir

Mex $225.08

Mex $ 112 .00 Mex $112.00

4.6
Elegir