Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Freud 12-096 - Broca recta de doble flauta de 15/64 pulgadas x 3/4 pulgadas (vástago de 1/2 pulgada)

Envío gratis en pedidos superiores a Mex $600.00

Mex $622.94

Mex $ 317 .00 Mex $317.00

En stock

1.Tamaño:1 Count (pack Of 1)


2.:Broca Recta De Doble Flauta De 1 Pulgada De Diámetro Por 1-1/4 Pulgada De 1/2 Pulgada


Acerca de este artículo

  • El producto es 1/2x2-1/2 broca estrecho
  • Fácil de usar
  • El producto está fabricado en China
  • Corta todos los materiales compuestos, madera contrachapada, maderas duras y maderas blandas
  • Uso en CNC y otros enrutadores automáticos, así como enrutadores portátiles de mano y de mesa, importados


1,27 cm (diámetro) Broca recta de doble flauta con vástago de 1/2 pulgada, longitud total de 4-3/8 pulgadas


Armando
Comentado en México el 11 de enero de 2025
El filo le dura cerca de unas 15hrs de uso, tomando en cuenta los diferentes derivados de madera y madera que he utilizo, mayormente melamina. Es buena pero por la marca esperaria un poco mas de filo, tengo 1 año con ella y despoztilla la melamina bastante, practicament ya me acabe todo el filo de la flauta en todo lo largo ya que le he cambiado la profundidad para realizar cortes limpios.
Alejandro Martínez
Comentado en México el 8 de abril de 2024
La herramienta tiene buenos acabados, mostrando que es una herramienta de calidad, la marca no defrauda. Es garantía.
Toño
Comentado en México el 14 de agosto de 2023
Estoy muy contento con este producto, ya que lo compre para hacer cajas en una escopleadora casera que me fabrique y el resultado es excelente, estoy muy satisfecho por la calidad del producto cita excelente y muy limpio, la verdad vale la pena ka inversión.
Nestor Gomez
Comentado en México el 1 de mayo de 2021
Excelente calidad, muy recomendado
Cliente frecuente
Comentado en México el 24 de febrero de 2021
Marca, calidad y país de fabricación son garantía de precisión y excelencia
el_Torques
Comentado en México el 8 de diciembre de 2021
Buena herramienta de corte tanto para desbaste como para acabado.
Jean-Claude Bouthillette
Comentado en Canadá el 21 de enero de 2021
très bonne qualité
juan arce
Comentado en México el 13 de febrero de 2020
Excelente calidad, como todos los productos Freud
Customer
Comentado en Canadá el 29 de octubre de 2020
Well build and stay sharp even when heated. The carbide cutter stay sharp after many uses.
johannes van oosterom
Comentado en Australia el 7 de septiembre de 2020
A strong sturdy 1/2" router bit that can do two boards at once, making them identical, because the cutting edge is two inches long and made from Tungsten Carbide.
Juan Pablo Gasca Belman
Comentado en México el 28 de agosto de 2019
Muy buena herramienta con un excelente filo
Debbie
Comentado en Canadá el 11 de marzo de 2019
I will be using this to flatten very wide boards. I expect it will be a top quality bit so no qualms there. However, I have never had such a hard time removing a bit from the case. I finally built two small towers of boards to support the edges of the case so the case was upside down, I put a #2 Robertson screwdriver in the hole in the bottom of the case and beat very hard with a hammer. Once the bit fell out I tried various methods to get the rubber gasket off without slicing my hands. Finally I got a good grip on the sides of the bit and twisted the gasket. It slowly made its way down the bit and came off. Hopefully this will help someone else get their bit out of the case and keep their fingers intact.
Kerry Pierce
Comentado en los Estados Unidos el 29 de abril de 2010
The first thing that impresses you about this bit, is the size. It is really large. The cutters are huge and as such, require more care than usual, especially if you are using it in a hand held router.I've been using the bit in a 2 1/4 HP router, with a D handle installed. I jointed and squared 2 large boards 8ft x 12" x 3", hand held. I butted the router base against long straight edges and took cuts of about 1/16" to 1/8". The bit performed flawlessly, giving me very smooth edges on the boards, which were laminated 3/4" cabinet grade plywood (3) with a 3/4" layer of solid red oak. Of course, the 2 1/2" cutting length wasn't long enough to do the whole board. After making about a 2 1/4" cut with this bit, I turned the boards over and used a 1/2" trim bit, bearing on the bottom, to finish off the cuts. The job turned out great, only requiring light passes with a smoothing plane to finish off the job. I'm very pleased with the speed and ease that this bit jointed and squared these large pieces. Nothing else in my shop worked as well or as quickly.Now to the bad part. I got a little careless on the second board, while cutting one of the 8ft sides. I didn't keep the router dead flat on the surface and dipped into the cut. In a split second, that long cutter took a big bite out of the side and then climbed up and out of the cut, twisting me to the left. Fortunately, the D handle base is a very secure base, that allows you to have a very good hold on the router, so nothing happened other than scaring me half to death. But, if someone had been standing close to me on the left, the router would have been in their face in an instant. I've been using routers for over 30 years and never had a router do that to me before. Of course, I usually use a router table when possible, which is the sensible thing to do with such large bits.I've got other projects planned, where I'll be using this bit and router configuration again as a hand held jointer. But, the next time, I'll make and install a much larger router base plate that will keep the router flat on the work surface. That should make things idiot proof....
Productos recomendados

Mex $557.41

Mex $ 295 .00 Mex $295.00

4.8
Elegir