No hay artículos en el carro
No hay artículos en el carroMás información del producto
Tips and Recommendations
Recommended speed settings above
- Use the sides of the cutter (Rather than the tip) for effective cutting
- Use higher speeds for hard woods, slower speeds for metals
High Speed Cutters
Carving Soft Materials
Available in many shapes, high speed cutters are used in carving, cutting and slotting in wood, plastics and soft metals such as aluminum, copper, and brass. These are the accessories to use for freehand routing or carving in wood or plastic and for precision cutting. Made with high quality steel. 1/8" shank.
- Wood
- Plastics
- Soft Metals
Tips and Recommendations
Recommended speed settings above
- Use the sides of the cutter (Rather than the tip) for effective cutting
- Use higher speeds for hard woods, slower speeds for metals
Structured Tooth Tungsten Carbide Cutters
Carving Soft Materials
Fast-cutting sharp teeth for greater material removal with minimum loading. Use on fiberglass, wood, plastic, epoxy, rubber, laminates, particle board and ceramic tile. 1/8" shank.
- Fiberglass
- Wood
- Plastic
- Epoxy
- Rubber
- Laminates
- Particle Board
- Ceramic Tile
Tips and Recommendations
Recommended speed settings above
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics (to avoid melting at the point of contact). If chattering occurs, increase speed.
- Do not use this cutter for drilling holes or for enlarging holes that are less than twice the diameter of the cutter. The tungsten carbide surface can easily catch the side of a hole and break the bit.
Tungsten Carbide Cutters
Carving Hard Materials
These are tough, long-lived cutters for use on hardened steel, fired ceramics and other hard materials. They can be used for engraving on tools and garden equipment. 1/8" shank.
- Hardened Steel
- Stainless Steel
- Cast Iron
- Nonferrous Metals
- Fired Ceramics
- Plastics
- Hardwood
Tips and Recommendations
Recommended speed settings above
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics (to avoid melting at the point of contact).
- If chattering occurs, increase speed.
Engraving cutters
Engraving Soft Materials
This group has a wide variety of sizes and shapes, and are made for intricate work on ceramics, wood carvings, jewelry and scrimshaw. They often are used in making complicated printed circuit boards. They should not be used on steel and other very hard materials but are excellent on wood, plastic and soft metals. 1/8" shank.
- Wood
- Fiberglass
- Plastic
- Soft Metals
- Ceramics/Greenware
- Jewelry
- Scrimshaw
Tips and Recommendations
Recommended speed settings above
- Use higher speeds for hard woods and slower speeds for metals.
- If chattering occurs, increase speed.
Diamond Wheel Points
Engraving Hard Materials
For fine detail work, cutting, engraving, carving, touch-up and finishing. Bits are covered with diamond particles. 1/8" Shank.
Not recommended for drilling.
- Wood
- Jade
- Cermaic
- Glass
- Semi-precious stones
- Hardened steel
- Other hard materials
Joel Righter
Comentado en Canadá el 23 de enero de 2017
Just another bit for the Dremel collection. Many useful situations can be found for it, but I have yet to use this exact one but the others have been great.
michel jodoin
Comentado en Canadá el 23 de enero de 2017
very good
Graham
Comentado en el Reino Unido el 21 de agosto de 2015
Works fine
qwert
Comentado en Japón el 17 de abril de 2015
切れが悪く、刃物としては落第点。多少高くても、まっとうなものを買った方が良い。
L Thachuk
Comentado en Canadá el 12 de marzo de 2014
Bought two of these to use for grinding after the many other cheap ones which came with my original tool were not up to the task. Have used it once and it works very well and shows no sign of wear.
Productos recomendados