No hay artículos en el carro
No hay artículos en el carroMás información del producto
Tips and Recommendations
Recommended speed settings above
- Use the sides of the cutter (Rather than the tip) for effective cutting
- Use higher speeds for hard woods, slower speeds for metals
High Speed Cutters
Carving Soft Materials
Available in many shapes, high speed cutters are used in carving, cutting and slotting in wood, plastics and soft metals such as aluminum, copper, and brass. These are the accessories to use for freehand routing or carving in wood or plastic and for precision cutting. Made with high quality steel. 1/8" shank.
- Wood
- Plastics
- Soft Metals
Tips and Recommendations
Recommended speed settings above
- Use the sides of the cutter (Rather than the tip) for effective cutting
- Use higher speeds for hard woods, slower speeds for metals
Structured Tooth Tungsten Carbide Cutters
Carving Soft Materials
Fast-cutting sharp teeth for greater material removal with minimum loading. Use on fiberglass, wood, plastic, epoxy, rubber, laminates, particle board and ceramic tile. 1/8" shank.
- Fiberglass
- Wood
- Plastic
- Epoxy
- Rubber
- Laminates
- Particle Board
- Ceramic Tile
Tips and Recommendations
Recommended speed settings above
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics (to avoid melting at the point of contact). If chattering occurs, increase speed.
- Do not use this cutter for drilling holes or for enlarging holes that are less than twice the diameter of the cutter. The tungsten carbide surface can easily catch the side of a hole and break the bit.
Tungsten Carbide Cutters
Carving Hard Materials
These are tough, long-lived cutters for use on hardened steel, fired ceramics and other hard materials. They can be used for engraving on tools and garden equipment. 1/8" shank.
- Hardened Steel
- Stainless Steel
- Cast Iron
- Nonferrous Metals
- Fired Ceramics
- Plastics
- Hardwood
Tips and Recommendations
Recommended speed settings above
- Use higher speeds for hard woods, slower speeds for metals and very slow speeds for plastics (to avoid melting at the point of contact).
- If chattering occurs, increase speed.
Engraving cutters
Engraving Soft Materials
This group has a wide variety of sizes and shapes, and are made for intricate work on ceramics, wood carvings, jewelry and scrimshaw. They often are used in making complicated printed circuit boards. They should not be used on steel and other very hard materials but are excellent on wood, plastic and soft metals. 1/8" shank.
- Wood
- Fiberglass
- Plastic
- Soft Metals
- Ceramics/Greenware
- Jewelry
- Scrimshaw
Tips and Recommendations
Recommended speed settings above
- Use higher speeds for hard woods and slower speeds for metals.
- If chattering occurs, increase speed.
Diamond Wheel Points
Engraving Hard Materials
For fine detail work, cutting, engraving, carving, touch-up and finishing. Bits are covered with diamond particles. 1/8" Shank.
Not recommended for drilling.
- Wood
- Jade
- Cermaic
- Glass
- Semi-precious stones
- Hardened steel
- Other hard materials
ivan messinger
Comentado en los Estados Unidos el 10 de marzo de 2025
Amazing Bit !!!
Customer
Comentado en Canadá el 20 de febrero de 2024
TThe Dremel 9901 Tungsten Carbide Cutter, Silver works well in my DREMEL TOOL, and serves as a CHAIN SAW Chain Touch Up Tool, for sharpening the chain, without removing the Chain from the cutter bar.GREAT for my requirements in the field.
購入者
Comentado en Japón el 25 de diciembre de 2024
かなり使ってるが折れないし摩耗しない。
Ronaystein
Comentado en México el 17 de enero de 2024
Tenia mis dudas por el precio, pero funcionan muy bien, lo he utilizado para cortar acrílico de 3 y 5 mm.
Marco Antonio Cruz Galvan
Comentado en México el 30 de agosto de 2023
Lo utilizo con un moto tool milwaukee de 12 volts y funciona de maravilla. Desbasta el material con mucha facilidad y es muy resistente. Se atoro en algunas ocasiones por descuido mío y reboto fuerte pero no se dobló ni se rompió.
Ruiseñor
Comentado en México el 14 de noviembre de 2023
Me gustó la rapidez
Juan Nuñez
Comentado en México el 7 de marzo de 2021
le cuestan maderas muy duras y las quema
R.I.T.H
Comentado en México el 11 de marzo de 2021
Muy buena calidad en todos los aspectos, pequeñita pero picosa, lamentablemente por eso la perdí pero ya ordene otra
k_tok2
Comentado en Japón el 28 de marzo de 2020
安い製品を使ってみたりしましたが、直ぐにダメになったりするので、やはり長い目で見れば純正品が良いと思います。
Abhijeet Sawant
Comentado en India el 4 de diciembre de 2020
Very good product & also packed & couriered very well very good seller
Aldo Espinosa
Comentado en México el 6 de junio de 2019
Tiene excelente filo
Arturo Garcia Smith
Comentado en México el 26 de marzo de 2018
me sorprendio como rebajo el metal pues no confie mucho al principio pero despues de ver como trabajo mejor que los discos de la esmeriladora compre mas de estas fresas
JorgeRG85
Comentado en México el 10 de abril de 2018
Muy buena calidad a un costo aceptable. Yo siempre he comprado DREMEL y lo seguiré haciendo. La verdad un muy buen producto
Productos recomendados
Mex $135.00
Mex $ 76 .00 Mex $76.00
Mex $215.59
Mex $ 127 .00 Mex $127.00
Mex $289.00
Mex $ 144 .00 Mex $144.00
Mex $262.62
Mex $ 154 .00 Mex $154.00