No hay artículos en el carro
No hay artículos en el carroEsta broca recta cuenta con longitud de corte larga y longitud total. Puede soportar incluso la carga de trabajo más pesada y aún así le da un corte suave y preciso cada vez. También proporcionan una expulsión excepcional de viruta para permitir un corte más limpio y más constante. Para ser utilizado en madera, compuestos de madera para múltiples aplicaciones tales como juntas en ángulo recto, juntas de caja, mortaja y tenones, conejos, uniones de la lengua y ranura, etc. Después de una prueba realizada por Wood Magazine, los bits naranja CMT han sido clasificados como los primeros bits generales del router en comparación con otras marcas.
Customer
Comentado en Canadá el 27 de diciembre de 2023
Parfait pour machiner ces banques a l’aide de ma CNC
Jay B. Sigel
Comentado en los Estados Unidos el 10 de diciembre de 2019
This is one big 1/2" router bit with a 2 1/2" cutting length. I needed this to cut a slot length-wise into a rectangular, mahogany (sapele) blank prior to turning it on a lathe for making wheel supports for a spinning wheel. It is the easiest and safest way to cut a slot into a (future) rounded post. I used this in my Rockler router table with a Porter Cable router. With the router cranked to its lowest position, the bit still protruded about 1/8". After testing the bit on some scrap, I set starting and stopping points on the table for the slot and using gradual height increases of 3/8" per cut, I safely achieved the desired results. Then I was able to turn the piece in the lathe without problems. (Prior to using this technique, I tried cutting the slots after turning the wheel supports using a table saw [really dangerous] or band saw [hopelessly inaccurate]. Both resulted in less than acceptable appearances.)Again, go slowly, at most 1/4 to 3/8" increments at a time. If you attempt to use the entire cutting surface in a single slice, the resulting disaster will be your own fault.
Brad Clark
Comentado en Canadá el 2 de diciembre de 2017
Great bit works good. Would buy more. Fast shipping.
Manut2500
Comentado en Francia el 1 de enero de 2017
très bonne fraise, taillant très efficace. permet la découpe de plan de travail de cuisine avec finition en un seul passage. pour defonceuse puissante. livraison rapide et sérieuse.
Yusuke Heller
Comentado en los Estados Unidos el 14 de diciembre de 2016
Good cutter. It worked well for the deep mortising with a router I needed to do. Held up well, though I will have to have it resharpened at this point. Mind you, I used this cutter to plunge through all sorts of different hardwood species. Anything from Desert Ironwood (extremely hard, dense, blunts cutters) Walnut, Hard Maple, Paduk, Box Elder Burl, Big Leaf Maple Burl, Quilted Maple, etc, etc. Name the species of wood except for Ipe and I've probably cut it with the same cutter over x amount of months. When I would prep blanks I was literally loading a jig with the blank and plunge boring (Fast, about 10 seconds per cut or less depending on the wood density- ironwood, slower of course) and it cut. Eventually it began to cut with burn and I replaced it with the same size Bosch cutter. I still have it, no chips in the carbide. for the amount of work this bit did for $28 or so at the time I bought it, it paid for itself a-thousand-fold.
Productos recomendados
Mex $1,071.54
Mex $ 557 .00 Mex $557.00
Mex $454.78
Mex $ 218 .00 Mex $218.00
Mex $391.91
Mex $ 176 .00 Mex $176.00
Mex $387.96
Mex $ 209 .00 Mex $209.00
Mex $932.23
Mex $ 419 .00 Mex $419.00