No hay artículos en el carro
No hay artículos en el carroCaja de impresora 3D TOPCUBE para Bambu Lab A1 Mini Combo
YM
Comentado en los Estados Unidos el 20 de marzo de 2025
Perfect width for the A1/Mini plus AMS. I won't be using it for that combo because of where my A1M is located, but it's large enough to fit most standard sized printers no problem. The extra width is really nice for adding things like tools, extra build plates and a heater. I have a similar setup for a different printer and it works really well.Four key features for me personally that I've been loving about this and similar enclosures I own are:1. the temp/hygrometer. This is especially useful in the winter since my printers are in the basement and it can be between 5-10°F colder than the rest of the house.2. The wrap around window. This is HUGE for easily accessing the printer (or AMS if that applies to you). Especially if you're using a CoreXY printer that has its filament holder on the back. This makes life way easier.3. This has an aluminum frame that easily clicks together. This, in my opinion, is better than others I've tried that have fiberglass rods. Those ones are significantly more difficult to assemble.4. The number of port holes around it. 2 grommets in the back to route cables and 2 large large flaps for installing exhaust fans or heaters.This will probably work beautifully for a resin setup as well so long as your printers shroud can be removed from the front or is on a hinge.
Tim Corcoran
Comentado en los Estados Unidos el 12 de marzo de 2025
I have had a number of 3D printers from tiny toys to larger-than-I-really-need-but-boy-what-a-printer. For each of them I built an enclosure, usually from an IKEA base like a table (or in one case a door) and a lot of acrylic. I built one such for my Bambu A1-Mini and it has served me well for a year or more. However, when I upgraded by adding the AMS-lite recently I considered how to adapt my custom enclosure and decided it was time to build a new one. Then, this enclosure popped up and I decided why not give it a try? One thing I must mention is that the pictures in the listing are just renders, they make it look like the whole thing is solid and totally square. Of course it isn't, think of it as a nicely stitched and perfectly fitted aluminum fabric tent, and that's OK..The finished product is quite practical as an enclosure and fits both printer and AMS easily. I wish it was perhaps a few inches taller as the Bowden tubes from AMS to printer push against the ceiling but this doesn't seem to be problem. Assembly was easy, the tubing clicked together the way some tent poles do, with holes and spring studs. The instructions were excellent. Once the frame is assembled you slide it into the "tent" which is very neatly folded for shipping. The zippered door is basically the length of two sides of the enclosure, giving me excellent access when I need it. I like the inclusion of the Thermometer/Hygrometer in the top left corner so I can monitor both while printing. The printer comes with an excellent USB-powered lightbar that clips to any part of the framing that you want. I chose to mount it on the center crossbar in the roof. The material of the tent which is aluminized and very reflective makes the light bar even more efficient.In my self-made enclosure I had used a 70mm PC fan to extract fumes and a length of 3" insulated ducting (from Amazon) plus some 3D printed connectors. Imagine my delight when I discovered that 100% of my handiwork on the venting was reusable directly. On the left hand side of the enclosure are two flaps held down by velcro. The smaller one even has 70mm spaced holes for the fan attachment and was easy to work with. Topcube sell a venting kit if you don't want to build your own and they provide a carbon filter. There are also 2 rubber-grommeted ports at the rear of the enclosure for power and any other cables you might want to bring in.Overall I am impressed with the enclosure, I spent about the same money to build my last enclosure and it took so much time I could have spent printing. Recommended.Packaging was very neat and tidy in an astonishingly small cardboard box. The only non-recyclable packaging were a few plastic bags.
Hal F. White
Comentado en los Estados Unidos el 10 de marzo de 2025
No se pudo cargar el contenido.
Agent Squirrel
Comentado en los Estados Unidos el 9 de abril de 2025
This TopCube enclosure fits my A1 Mini almost perfectly. I can fit both the printer and the AMS Lite unit in the enclosure.Now, the A1 Mini is not meant to be enclosed. So I have found this is a great way to keep my printer clean and also keep the filament on the AMS Lite dry. I zip this up with some containers of desiccant around the AMS Lite and have noticed a difference.When printing things that take anywhere over half an hour, I leave the front open. This way the unit can still get air. The exception is a few PETG prints where I have found keeping the enclosure zippered up helps get more consistent results.It also does a decent job of dampening the printer's operational noise and definitely keeps dust off the mechanics, which is great.Assembly was mostly straightforward, though the instructions could have been a touch clearer in a couple of spots, and getting everything perfectly aligned took a little patience.Overall, it does what it's supposed to do – protects from drafts, reduces noise somewhat, and keeps things tidy. While the panel quality or assembly could be slightly improved, it's a solid and effective enclosure specifically tailored for the A1 Mini and a worthwhile upgrade if you're looking to stabilize the printing environment or reduce dust and noise. Recommended for A1 Mini owners wanting these benefits.
Tech Reviewer
Comentado en los Estados Unidos el 17 de abril de 2025
The price seems a little high, but all things considered, I really like this. Most enclosures are for just the printer, but if you've got an AMS, having it in there too is neat!In my case my AMS hasn't shipped yet, so for now I'm actually using it vertically to store my printer. I know the A1 series isn't meant to be an enclosed system, but I like that it contains the heat, smell, and noise, so I can run it in my bedroom overnight and not be bothered by it.
Productos recomendados