Carro de la compra

No hay artículos en el carro

No hay artículos en el carro

Bamboo Lab X1 Carbon, X1, X1C Hotend Kit completo para impresora 3D de la serie X1, extremo caliente de acero endurecido de montaje completo con ventilador, termistor, calentador de cerámica, boquilla

Envío gratis en pedidos superiores a Mex $600.00

Mex $1,298.19

Mex $ 597 .00 Mex $597.00

En stock
  • Kit completo de bambú Lab X1, X1C, X1 Carbon Hotend: extremo caliente de acero endurecido de montaje completo con ventilador, termistor, calentador de cerámica, boquilla de 0,4 mm, reemplazo de bloque de calefacción. Es compatible con filamentos de impresión 3D comunes como PLA y PETG, etc. No apto para X1E
  • Boquilla integrada única: la boquilla está integrada en el bloque de calor y conectada al disipador de calor a través de un tubo de metal fino para un rendimiento óptimo. Con este diseño, el hotend se calienta mucho más rápido que un hotend tradicional, y la estructura integrada reduce eficazmente los problemas potenciales al reemplazar la boquilla.
  • Calentamiento rápido y temperatura precisa: el calentador de cerámica puede calentar la boquilla hasta 300 ℃, mientras que el termistor tiene una medición de temperatura altamente precisa y un diseño estructural confiable.
  • Ventilador de refrigeración de seguridad: el ventilador de refrigeración para hotend tiene una función de apagado automático mientras se bloquea a voltaje nominal durante 1-3 segundos. El circuito intenta torestartin de 2 a 6 segundos. No hay daños después de 72 horas de bloqueo.
  • Instalación sin complicaciones


Bamboo Lab X1 Carbon, X1, X1C Hotend Kit completo para impresora 3D de la serie X1, extremo caliente de acero endurecido de montaje completo con ventilador, termistor, calentador de cerámica, boquilla de 0,4 mm, reemplazo de bloque de calefacción extrusora


Norm D’Gear
Comentado en los Estados Unidos el 6 de marzo de 2025
If you have an X1C this is the same hot-end the machine shipped with. Fortunately, it is not 'made for bambu'; it's the actual OEM part. My original hot-end ran for hundreds of hours, and I'm sure this one will, too. This is an easy install since it's an even swap. The way this unit slides out isn't obvious, but with the screws removed you can work out the direction. The wires must be routed correctly so that the magnetic cover is positioned correctly. Note their position and the plug before removing the old one. The new wires have the matching plug installed, so there is no cutting, stripping, or soldering. Slide the new one in, install the new screws in the locations of the old ones, and plug it in. You should be back to printing. If you have done a cold-pull or cleared a clog on this machine, you have done 85% of this swap.
backwoods18235
Comentado en los Estados Unidos el 10 de marzo de 2025
Absolutely AMAZING! plug and go!!!!
Robert Buckley
Comentado en los Estados Unidos el 19 de febrero de 2025
This is not a stainless steel hotend as advertised. It is a hardened steel hotend. They are not the same thing.
ard78641
Comentado en los Estados Unidos el 1 de abril de 2025
Exactly like oem might even be oem hard to tell.
Productos recomendados

Mex $719.10

Mex $ 373 .00 Mex $373.00

4.7
Elegir

Mex $599.00

Mex $ 275 .00 Mex $275.00

4.5
Elegir

Mex $660.00

Mex $ 336 .00 Mex $336.00

4.6
Elegir

Mex $505.41

Mex $ 227 .00 Mex $227.00

4.3
Elegir

Mex $954.71

Mex $ 505 .00 Mex $505.00

4.9
Elegir