No hay artículos en el carro
No hay artículos en el carroCustomer
Comentado en los Estados Unidos el 24 de abril de 2025
Great durability easy to install
D. Slyzack
Comentado en los Estados Unidos el 30 de agosto de 2022
Pros:- You won't find anything in this size that's cheaper- The picture brightness and quality is excellent- No wrinkles aside from the extreme corners- Compared to other vinyl screens, the smell is quite low and goes away after 24hr.Cons:- Their assembly video is for an older model that uses riveted holes instead of the tension rods. Please post a video that uses the updated model.- Mounting hardware can only be mounted to studs on on side of the two screw tracks as studs are ~2in wide and the screw holes exceed this. I put both screws vertically aligned on opposite screw tracks and it mounted fine.- Tensioning. Oh boy this was difficult. On the second attempt, I aligned the frame down the millimeter on every corner and made sure to attach springs on opposite sides in pairs to prevent the material from shifting. Even after doing all of this and spending two hours doing it, ended up with two minor ripples in the top left and right corners. I did the suggested massaging of the corners as stated in the manual, however this did not improve it. These are fairly minor, but I feel like the company should address this. It seems the screen is ever-so slightly too small and the material is not getting pulled tight enough on the corners compared to the rest of the screen.- The middle bar needs to be better secured as even lifting the final screen from the top aluminum frame is enough to dislodge it.- The company needs to tighten the manufacturing tolerance of the black border as it's a few mm too big and is slightly wavy.Overall, while this was a pain to assemble, the results are great. Again I have to state that it's a bit unfair to knock this screen too much as for the price and size, it cannot be beat. With such a low price I think you have to ultimately accept some things.
MaV
Comentado en los Estados Unidos el 26 de noviembre de 2022
Pros:Image quality. Wow. Nothing even close to projecting against the wall. Colors are brighter and allow for a nice, colorful and clear image.Very thin "bezels" which provides with a great looking quality screen.Came with extra screws and tools to get the screen set.Cons:Installation. While it is not that difficult, there are certain steps that are just shown on the video and on the instructions but require to pay attention to make sure it allows for a smooth surface on the screen side.Some screws were really low quality (specifically, the one to hang the screen to the wall). I skipped them and used some of mine.Other thoughts:Here are a few tips to installing this screen:1) Make sure you have plenty of space and 2 people available to put it together. I did it by myself and it felt harder than it should have been.2) Check you have all the parts. They give you extra screws, but sometimes, things do not fully match properly, so make sure you have everything beforehand.3) when putting it together, make sure you center the material for the screen on the frame. Otherwise, you may run into small folding issues on the corners. Since you may have the screen side looking down, you may not see it until you are doing setting it up, and then finding out the imperfections. Here is where the "2 people" can help. As long as both people are doing the opposites springs, you will be fine.4) Skip the mounting screws. Horrible and were stripped very quickly. I used my own.Once I was done with the installation, I loved it. Get it.
DrH
Comentado en los Estados Unidos el 18 de noviembre de 2020
I have no complaints about the screen after I was able to get it assembled. It provides a nice smooth surface and I like the narrow black satin frame. I have an Epson 5050 projector and it looks fantastic with this screen.BUT....I did have an issue that required me to redo the screen assembly which was frustrating and time consuming. If your screen comes with a supplied screwdriver that has what I would describe as short rubber hairs all around the handle.... THROW IT AWAY and use a different screwdriver. The problem is that this screwdriver SHEDS a bunch of those rubber hairs and if they fall off while you are assembling the screen they can lodge between the face of the frame and the back of the screen. And you won't likely notice this until you finish assembly and hang the screen, only to notice a bunch of very visible protrusions all around the screen edge (as happened in my situation). The only way to remove these is to disassemble the screen from the frame and locate and remove each of those little rubber hairs. WHAT A PAIN.Kudos to Akia for supplying assembly tools in the first place, too bad the supplied screwdriver turned out to be a dud. Perhaps they have fixed this problem and are now included a better screwdriver.Here are three suggestions that will help you with assembly:1. Toss the supplied screwdriver and use your own (as per details above)2. Use very fine grit sandpaper (220 grit) to sand down the joints of the aluminum frame where they meet in the middle of the face. The aluminum frame ends were very sharp with burrs left on the metal. If it wasn't for close inspection I am certain my screen material would have ripped upon stretching to fit. Use some 220 grit sandpaper to knock the edges down and make them mostly smooth.3. Perform step 7 of the instructions BEFORE step 6.Step 6 of the instructions has you hooking all the tension springs in place but then step 7 has you add rubber caps to the tension rods. THIS IS WRONG. Step 7 should come first- if you don't have those rubber caps on the tension rods when you have hooked all the springs, the sharp edges of the tension rods can tear the screen, as was the case in my situation. Additionally, attempting to put the rubber caps on the tension rods after the springs are in place is impossible, especially if the rods were too short (again, as was my case).
M. Silva
Comentado en los Estados Unidos el 24 de octubre de 2019
I am very pleased with the final result of the 125-inch fixed frame series AKIA screen. I was able to fully assemble the screen alone. I originally was concerned that the screen material would not stretch over the frame, and was certain that I was sent the wrong size screen. I contacted customer support by phone and was given encouragement that convinced me to continue. I reviewed several videos on assembly of these type of screens that use springs and slowly but surely was able to complete the process.My setup may be different than most. I basically did a ceiling mount (Actually floated from L brackets), so the frame is about 8 inches from my wall. This was needed as I had 2 windows behind my wall that would limit the size of the screen. Previously I had a 82 inch custom build projection screen that fit between the 2 windows on the wall. I always wanted to go much bigger on the screen but originally felt that would not be possible. Here is what I finally did:I added 6 L-brackets to the top of my wall. Four of the brackets would be to support the screen using the supplied Wall Brackets. (The directions tell you to use 2 of the brackets for the top and 2 of the brackets for the bottom. I changed this and placed all 4 of the wall brackets on the top.I purchased a large curtain rod from Amazon that was adjustable from 120 to 170 inches. This Rod was simply supported on the top of the 6 L-Brackets. I also purchased 8 Theater Grade Extreme 100% Blackout Grommet Curtain Panels, 52” x 95”. 6 of the panels were black and for the ends, I used 2 red panels. This took care of blacking out the background from the 2 windows, and I was now able to have full light control in the room.I was able to make 4 custom metal bracket adapters that I painted flat black, which allowed me to mount the screen to the L-Bracket and wall mounting brackets to float the screen. Wire or other mounting options would have worked here as well.The screen had a tendency to angle in toward the wall slightly. For this reason, I placed 2 additional L-Brackets at the bottom of the screen hitting the Frame so that the screen was now perfectly vertical. The curtain panels completely hide all brackets and the screen has a nice floating look.I am considering adding 2 4x4 blocks cut to size from floor to the bottom of the screen to relieve any pressure on the bottom of the screen. In all honesty, I am not sure this is even needed as the frame this screen is supported on is very heavy duty, and I doubt any sagging would occur over time.Overall, I am very happy with how this has turned out and I believe the screen is of exceptional quality and a very good product. The only issues I had are as follows:Tension Rods: Horizontal rods, were fine with proper overlap. The 2 Vertical rods were too short. The rod length just matched the length of the outside holes of the fabric. This result on one of the sides tearing through the mounting hole. I ended up having to purchase 2 brass rods of the same diameter to get some overlap for the springs to attach to the frame.While nowhere in the manual is this mentioned, I found it much easier to mount the screens with the spring oriented in a certain direction. One end of the spring seems to make a perfect half circle (Better for tension rod), and the other end, is less angled, and that end seems to more easily mount to the metal frame. Also, I found that in many cases it was easier to first start the spring by attaching it to the frame, and then pull it over through the tension rod hole.The supplied Allen wrench was not of the greatest quality. It was starting to strip as I was tightening the screws. I switched to a much higher quality Allen wrench I had, which greatly improved my ability to tighten down all screws without slippage or striping.Overall, I am very pleased with the result. It is a bit of work, and my fingers are still a bit numb from stretching the springs into position, but the supplied tool does get the job done.
Productos recomendados