No hay artículos en el carro
No hay artículos en el carroDiseñado para los lazos y ballestas más rápidos. El nuevo Quickfletch Hellfire fue diseñado para proporcionar lo último en precisión y silencio. Nuestra tecnología patentada de paletas NAP estabiliza la flecha o el tornillo más rápido que la competencia y proporciona una mayor precisión de largo alcance. Disponible en modelos de 2 pulgadas y de perfil bajo de 3 pulgadas para arcos verticales y perfil bajo de 3 pulgadas para ballestas de alta potencia
Noah
Comentado en los Estados Unidos el 10 de enero de 2025
These aren't half bad to be honest. I wouldn't say they're perfect and perfectly line up the fletching but it's pretty close for what I'm doing. I didn't use boiling water, I used a heat gun just fine. Just go slow and heat evenly.
Blaise
Comentado en los Estados Unidos el 6 de mayo de 2024
Simple application. Be careful to dip slowly and not to bump the fletching. I did have to remove and reapply one bolt.
nick zagami
Comentado en los Estados Unidos el 18 de enero de 2024
I put these on and yes I am shooting better! I love the stiff vanes. As far as slipping down the shaft I have not had that problem as others stated in the reviews.. But just to be safe i put a drop of super through the space on the nock side just before I dip it in the hot water. I expect that to hold them in place.
Curtis
Comentado en Canadá el 29 de octubre de 2021
Vanes do not line up on 2 in the pack of 6 and 2 others have massive blobs of glue all over the place, in summary 2 of the wraps actually function consistently and are actually very accurate. So you may have to sift through to find the good ones and always put them in the bag before you take them in the field.
LGL
Comentado en los Estados Unidos el 24 de septiembre de 2018
I use TenPoint Crossbow Pro Elite Carbon Arrows with Omni-Nocks. Although any vane can be placed downward in the barrel, the nock still requires careful indexing or the string rotates the arrow slightly to get in the slot--and sends the arrows sailing offline. I found this out using my Bohning Helix Tower Jig for crossbows. This was time consuming, messy with the glue, and no matter how carefully I aligned the omni-nock triangle (visible on the back of the nock) with one of the vanes, about 1/3 of my arrows didn't fly well. They spiraled off target by 8 to 12 inches, but the ones that aligned OK had tight groups out to 40+ yards. The ones that were indexed well flew better than the original vanes--much better groups with these properly indexed helix vanes..With these Hellfire Crossbow Fletchings I can get small groups again--they do seem to stabilize the flight well. But, the upside is that I am able to correctly index the nocks so that the omni-nocks catch the string in one of the 3 groves! Every one I've done flies well. Upside two: I boil a pot of water and put it into a 9" stainless steel drink cup, and then proceed to fletch 6 arrows in about 10 minutes. No mess. No glue. Good indexing. Good groups. No brainer..I can't speak to the claim that the raised edge begins to spin sooner and that these NAP fletchings are better/worse than others, but they do spin enough to make much tighter groups than the slight-right (I think they are 1 degree right) tenpoint factory vanes. They are as accurate as the helix (5 degree right) vanes--which means that they should work great stabilizing broadheads..I can't speak to longevity, but so far they seem to take target practice (field points) well--no damage from target hits/removal. . .
Productos recomendados
Mex $166.00
Mex $ 91 .00 Mex $91.00
Mex $605.92
Mex $ 296 .00 Mex $296.00
Mex $147.29
Mex $ 88 .00 Mex $88.00