No hay artículos en el carro
No hay artículos en el carroMando a distancia para puerta de garaje Wayne Dalton Wayne Dalton 309884 3910 297132 303 MHz
Compatible con modelos de apertura de puertas de garaje Wayne Dalton Classic Drive con radio frecuencia de 303 MHz. Classic Drive modelo 3012, 3016 y 3512 Quantum, 3212, 3213 y 3412
Esta unidad reemplaza al modelo que ya no está disponible 02-3047-3BUH, 297132 y 02-3047-1BUH
sellers
Comentado en los Estados Unidos el 13 de marzo de 2024
I was very hesitant to order these as we have 25 year old Wayne Dalton Quantum 3213 and never had luck programming them to the universal remotes that are now available in vehicles. And some reviews stated they did not work with their 3213 model. Our old remotes were near total death.. So I decided to give them a try before we paid big bucks to have a garage door company come out to help. Definitely follow Dan B’s instructions because the enclosed orders are useless. It was a breeze to get them to sync. I could not have been more overjoyed. Thank you Dan B!
Miplumber
Comentado en los Estados Unidos el 27 de febrero de 2024
Are these as good as the originals? No, do they work, yes. Have to push button hard and in just the right spot. Set up was super easy.
C. Jones
Comentado en los Estados Unidos el 17 de octubre de 2024
Ordered 2 of these remotes. No green light appears at all, and no noise sounds -- pressed all 3 buttons. Therefore, can't program them!! If it's the batteries that are bad, which is possible, I don't think I should have to pay more to replace them. Product should be sent with fresh batteries!!
Steve Gladden
Comentado en los Estados Unidos el 28 de diciembre de 2023
Trash the instructions that come with the item. Find Dan B’s review and follow his instructions. I would recommend the seller to add Dan B’s instructions to each purchase as these are the only instructions that work.
DAN B
Comentado en los Estados Unidos el 11 de agosto de 2021
DID NOT COME WITH INSTRUCTIONS!So either search online for Wayne Dalton 309844, or use this information, pasted from there. Follow ALL the instructions.Programming a Transmitter (1,2 or 3 button) to a Quantum™ and Classicdrive™ OpenerNOTE: You must change the transmitter’s code before programming the transmitter to the motor head unit.Changing the Transmitter Code1. Press and hold the button on the transmitter that you want to change. The GREEN LED will flash once andthen turn off.2. Continue to hold the button until the GREEN LED begins to flash (approx. 10 seconds).3. When the GREEN LED flashes, immediately release the button and then immediately press and hold thesame button again. The GREEN LED will now come on steady.4. Continue to hold the button until the GREEN LED begins to flash (approx. 5 seconds).5. When the GREEN LED flashes, immediately release the button.6. The code for this button has now been changed to a new randomly generated code. Do not press the buttonagain until instructed in “Programming Transmitter to Power Head Unit”.7. You must now re-program this transmitter to the motor head unit. See “Programming Transmitter toPower Head Unit” below.Programming Transmitter to Power Head Unit1. Press the PROGRAM button located on the garage door motor head unit once. The PROGRAM STATUSlight on the motor head unit will turn on and remain lit for one minute, indicating that it is ready to learn theTransmitter code.2. Press the same button on transmitter as you did in “Changing Transmitter’s Code” above. The PROGRAMSTATUS light will turn off indicating a successful learn.3. Press the same button on the Transmitter once more to operate the door.4.If you are unsuccessful in programing the transmitter to the motor head unit or if the button does notoperate the door or if you wish to program another button to operate a different door, you must change thetransmitter’s code.BatteryIf the LED does not turn on when button is pressed, replace battery.
Productos recomendados